飞利浦工厂调试与设置说明Word下载.docx

1、B-DRV蓝驱动Blue driver3、当用于维修时，可用一条亮线状态来大致调准暗平衡。当然处于“B/W BALANCB”状态时，按MUTB键，则可进入一条亮线状态；再次按MUTB键时，When it is used for maintenance, wed better use bright-line status to approximately adjust the dark balance. Of course, in the state of “B/W BALANCE”, the screen will turn into one bright-line status after

2、pressing the MENU key. Press the MEMU key again,A、则可由亮线状态返回到全屏状态。A. The bright-line status returns to the full screen.B、在此页调试下，按TV/AV键，屏幕会显示软件设计的内部亮或暗场信号，便于工厂进行亮/暗平衡的调试。B. In this page, press the TV/AV key, then the screen will display the software internal bright/dark field signal which is convenie

3、nt for the manufacturer to debug the light/dark balance.二：调试项的调节及设置项的设置/Items adjusting and setting1、操作方法：/Operation methodA、按PROD键进入调试状态。A. Press the PROD key to enter the debugging status. Or B、用MENU键向上翻页或用CALL键向下翻页到要调整的项目所在的页面。B. Press the MENU key to page up or press the CALL key to page down to

4、 the page where the items are adjusted.C、用P+/P-选择到要调整的项目。处于调试菜单的0:90显示时，可用09键直接快速选到对应当前页的09行。C. Press the P+/P- key to select the items to be adjusted. If the debugging menu is displayed with 0:90, the numeric 0-9 keys can be used to correspondingly select the 0-9 lines on the current page rapidly.D

5、、用户普通遥控器实现“工厂”，按键功能，按遥控器MENU（菜单）键进入PICTRUB（图像）调整界面，然后直接被遥控器上的数字键6、5、6、8即可进入工厂调试状态。D. Achieve the key-pressing function of “plant” with the common remote control. Press the MENU key on the remote control to enter the PICTURB adjusting interface, then directly debug the plant through pressing the nume

6、ric keys 6, 5, 6 and 8.2、调试项及设置项说明：/Notes for the debugging and setting items（MENU 0） 项目号/Item No.说明/Notes参考值/Reference ValueH. PHASE行中心（范围：063）Horizontal center （scope: 063）401V. SIZE场幅（范围：V- amplitude （scope:442V. LINE场线性（范围：Vertical linearity （scope:343V. POSITION场中心（范围：Vertical center （scope:414

7、VSC场SC校正（范围：031）VS-correction （scope: 031）5MTHPHASENTSC制行中心（范围：-61+63）NTSC horizontal center（scope -61+63）6NT. V. SIZENTSC制场幅NTSC vertical amplitude7NT. V. LINENTSC制场中心偏差量NTSC vertical center derivation8NT. V. POSITION场飘移调整（范围：-53+63）Field drift adjustment（scope: -53+63）9NT. V. SCMTSC制场SC校正偏差量MTSC V

8、SC-correction derivation （scope -61+63）10H. BLK.START行左消隐（范围：0+15）Horizontal blanking left （scope: 0+15）11H. BLK. END行右消隐（范围：Horizontal blanking right（scope:注：在此页调试项下，按TV/AV键，屏幕会显示软件内部“田”字信号，便于工厂进行图象的几何调节。Notes: under the debugging items of this page, press the TV/AV key, the screen will display the

9、 signal looking like the shape of “田” in the software, which favors the geometric adjustment of the picture by the plant.（MENU1）项目号/ItemsRF.AGCRF. AGC3%ASD.IL.POST.50PNL制式OSD左右位置PNL. OSD. horizontal positionASD.V.POST.50511：可调范围：060Adjustable range: 06016：063 06314OSD. CONTOSD文字对比度OSD text contrast1

10、8HALF TOME菜单半透明 0：关闭 1：打开Menu semitransparent0: OFF 1: ONICON菜单顶部图标及背景 0：Menu top icon & backU LIME菜单底部装饰条 0：Menu bottom decorative stripSELECT SET置1进入后续工厂设置Set 1 to enter the subsequent factory setting（MENU2）ACCSACC控制速度ACC control rateVIF. SYS. SW中频设定Setting of intermediate frequency380MOIFIF解调偏置，用

11、来调节图像干扰伴音IF demodulation bias, used for adjusting the image disturbing audioTUNER UHF频率合成高频头U段位码设置Bit code setting of frequency synthesis high frequency tuner U sectionVL/VH FREQ高频头的VL/VH分频点选择VL/VH crossover frequency selection of high frequency tuner45VH/UHF FREQ高频头的VH/UHF分频点选择VH/UHF crossover freq

12、uency selection of high frequency tuner125SEL TUNER高频头设置，0率合成, 1电压合Setting of high frequency tuner, 0 frequency synthesis, 1 voltage switch-offBAND SETL、H 段高低电位选择High/low potential selection of L, H sectionsF SEARCH快速搜台开关Fast search switch（MENU 3）CHINESE中文 0：Chinese 0:THAI泰语 0：Thai 0:VIETNAM越南语 0：Vi

13、etnamese 0:INDONESIA印尼语 0：Indonesian 0:FRENCH法语 0：French 0:D/K伴音D/K开关 0：Audio D/K switch 0:B/G伴音B/G开关 0：Audio B/G switch 0:I伴音I开关 0：Audio I switch 0:M伴音M开关 0：Audio M switch 0:（MENU4）PF P4PAL制式时清晰度提升频率PAL. sharpness raising frequencyPF PMPAL. Sharpness raising frequencyPF N4NTSC 4.43 MHz制时清晰度提升频率NTSC

14、 4.43 MHz. sharpness raising frequencyPF. NMNTSC-M 制时清晰度提升频率NTSC-M. sharpness raising frequencyPF SECSDCAM制式时清晰度提升频率SDCAM. Sharpness raising frequencyPF AVAV时清晰度提升频率AV. sharpness raising frequencyXTAL ALICM晶振谐振电容补偿XTL resonance capacitance compensation AFTER SHOOTRatio Per and After Shoot 图像勾边Ratio

15、Per and After Shoot edge enhancementOVER SHOOTRatio Per and Over Shoot 图像勾边Ratio Per and Over Shoot edge enhancement（MENU 5）X-RAYX 射线保护X-RAY protectionAKB自动暗平衡设置Automatic dark balance settingCATHODE LAE阴极驱动电平Cathode driver power levelV GUARD场保护功能Vertical guard functionSOFT GUARD当产生保护后，系统会自动重启，如果DFL关

16、闭，则系统会用正常模式重新启动，否则系统会以软启动方式重新启动，起始值：When the guard is generated, the system will restart automatically. If the DFL is closed, it will restart in normal mode; otherwise, it will restart in soft startup mode. The starting value is 0.V. MUTE. P. OFF显像管的视频输出Kinescope video outputHBL左右消隐开关Horizontal blan

17、king switch（MENU 6）BLOC暗电平偏置曲线设置; 配旧管时推荐值要调大Dark power level bias curve setting; increasing the recommended value when the old kinescope is furnishedBLK. STR. DEP黑延伸深度Black extension depthBLK. AERA暗电平延伸使能区域大小选择Selection of black power level extension areaSECAM BLKSECAM 信号黑电平偏置调整Black power level bia

18、s adjustment of SECAM signalWPL白峰限制开关White Peak limit switchWPL DAC峰白分割点的设置Setting of white peak breakpointWPL CLIP峰白分割电平White peak clip power levelVIDEO LEVEL视频信号输出（PINI）幅度Video signal output（PINI）level（MENU 7）YD.PALPAL亮色时延差PAL bright color time-delay deviationYD.NTNTSC亮色时延差NTSC. bright color time-

19、delay deviationTD.SECSECAM亮度，色度时延差SECAM brightness, color time-delay deviationYD. AVAV亮色时延差AV bright color time-delay deviationED.YCSYIIS亮色时延差SYIIS bright color time-delay deviationCOL.FREQ彩色负载度，中心频率设置Color load，setting of center frequencyCOL.EYPASS色彩基带通道延迟设置Delay setting of color base band passageM

20、ETRIC OPT脚码矩阵选择设定Subscript matrix settingCHSB彩色灵敏度设定Color sensitivity settingFORCE COL强制彩色开关Forced color switchAUTO COL LIWIT自动色度限制Automatic color switch（MENU 8）ST BRT标准状态下亮度的设置（由客户设置）Brightness setting under standard state（set by user）80ST.CONT标准状态下对比度的设置（由客户设置）Contrast setting under standard state

21、（set by user）75ST. COLOR标准状态下色度的设置（由客户设置）Color setting under standard state（set by user）60ST. SHARP标准状态下锐度的设置（由客户设置）Sharpness setting under standard state（set by user）30LT. BBT明亮状态下亮度的设置（由客户设置）Brightness setting under bright state（set by user）LT. CONT明亮状态下对比度的设置（由客户设置）Contrast setting under bright s

22、tate（set by user）LT. COLOR明亮状态下色度的设置（由客户设置）Color setting under bright state（set by user）LT. SHARP明亮状态下锐度的设置（由客户设置）Sharpness setting under bright state（set by user）YI. ITR艳丽状态下亮度的设置（由客户设置）Brightness setting under flaming state（set by user）64YI. CONT艳丽状态下对比度的设置（由客户设置）Contrast setting under flaming state（set by use