1、GHIJKLMNOPQRSTUVWXYZ步骤 Step检测项目 Item规格标准 Standard使用设备 Machine备注Step 1.机壳外观依附录二之规格执行目测全检Step 2.Display外观1. 依附录二之规格执行2. 检查LENS是否有翘曲、毛边3. 检查卡勾及螺丝是否至定位,卡勾处不可损伤或缺料目测/Step 3.间隙/段差/角度依附录三之规格执行目测/厚薄规StepInspection ItemStandardMachineRemarkStep 1Housing cosmeticAccording to appendix 2visual inspectionFull In
2、spectionStep 2Display cosmetic1. According to appendix 22.Check Lens 3.Check screwvisual InspectionFull Inspection Step 3gap/step/angleAccording to appendix 3visual inspection/feeler gauge检验方法:1.检验环境:光照度5001000lux目视 2.眼睛与被检测物体距离30cm(Logo和Label距离45cm),目检方向与检测物体呈90度直视,而后再以上、下、左、右各15度再检测一次。3.检测时间10s(Lo
3、go和Label 3-5S)。Inspection methodInspection condition : light source 500-1000 lux , visual inspectionInspection distance : 30 cm(Logo and Label is 45 cm), Parts will be viewed initially at 90 or perpendicular to the surface being inspected. The parts should then be rotated 15-degrees in four directio
4、ns (right, left, up and down) to detect defects not discovered in the initial viewing. Inspection time : 10 sec (Logo and Label is 35 sec.)附录一表面类别分类定界项目AA显示面项目: LCD透明显示区域(LCD和CLI)听筒上的logoCAMERA和CAMERA LENS平常使用,可直接看见暴露在外的表面部分 Housing A 可见面键盘(包括侧键音量控制键摄像扣电池盖锁扣)自视镜平常使用,次要看见暴露在外的表面部分 Housing侧面四周摄像头支撑外置卡
5、塑料外盖Housing B电池盖使用者不会直接看到的区域 Housing B内部电池盖背面电池SIM卡卡钩充电器等及其它部件。Appendix 1Handset cosmetics definitionInspection surface is classed as AA, A, B and C side, as followingClassDefinition & Item listInformation display area onlyItem: CLI and LCD transparent display area (LCD module & cover), Logo on hand
6、set, functional printing on keypad.Primary surface exposed to direct close-up view in ordinary use CLI and LCD cover painted area, plastic part of keypad, flip front housing (flip inner and flip outer) ,reflective mirror.Secondary surface exposed but not in direct view in ordinary use rear housing,
7、battery door, release button in battery door, side button. Surface not visible in ordinary use inside rear housing, battery door, battery, SIM card socket, charger, CF & SD Door, other accessory., other accessory.附录二FQC/OQC/CDIT外观检验标准1. LCD显示屏(模块)(Lens)ItemscopeAcc. numberRej. number灰层/脏污 直径 0.1mm 0
8、.1mm 0.15 mm-纤维丝(毛屑)长度 1.2mm且宽度0.08mm异色点 直径 0.1mm同色点凸点及凹点备注出现刮伤指纹胶带流痕等不良直接拒收不良点数大于等于3个也不可接受。Appendix 2Inspection standard1. LCD display area (include LCD module & cover)Dust/stain on transparent area diameter 0.1mmdiameter0.15 mm diameter Fiber or thin line on rim of LCD cover length 1.2mm and width
9、0.08mmImperfection of the contrasting color on LCD coverImperfection of the same color on LCD coverProtruded point or holes on the LCD CoverRemark: Automatic rejection for scratch, fingerprint, glue tape, flow mark or total number of defects equal to or above 3.2.键盘:同色点(键盘表面印刷) 直径 0.2mm异色点(键盘表面印刷)同色
10、杂点(键盘塑料部分) 直径 0.25mm 0.25 0.5 mm 直径 0.5 mm异色杂点(键盘塑料部分) 0.2 0.35 mm 直径 0.35 mm刮伤 长 1mm且宽 0.05mm 长1 2 mm且宽 0.05 mm 长 2 mm或宽0.05mm备注出现漏印气泡色差等直接拒收不良点大于等于3个也不可接受。2.keypad :Imperfection of the same color on printing diameter 0.2mmImperfection of the contrasting color on printingExtra point with the same c
11、olor on plastic part diameter 0.25mm diameter 0.5 mmExtra point with different color on plastic part diameter 0.35 mmScratch length 1mm and width 0.05mm 1 2 mm and width 0.05 mm length 2 mm or width 0.05mm Automatic rejection for no painting, bubble, discoloration or total number of defects equal to
12、 or above 3.3.Logo 和 Label(1.) 不可辨认的 logo & label都是不可接受的。(2.) 印刷不良: a.色差刻痕漏印锯齿在Logo上都是不可接受。b. 漏印在Label上是不可接受的刻痕及锯齿最多可接受一个不良。(3.) 角度歪斜不可超过5度I. Logo and Label(1).Both logo & label, not acceptable for illegible defect.(2).Printing incomplete:a.In Logo, not acceptable for discrepancy in color, notch, in
13、complete painting, sawtooth etc.b.In label, not acceptable for incomplete painting, maximum 1 notch or sawtooth is acceptable.(3).An inclined angle which is over 5 degree is not acceptable.4.外观(不包含LCD & Keypad 区)AreaScopeAcc numberRej. Number同色杂点 直径0.2 mm 直径 0.15 mm 0.1520mm 0.25 直径0.30 mm 0.30 mm 直
14、径 0.20 mm 0.20 直径 0.30 直径 0.50 mm 直径 0.50 mm异色杂点 直径 0.2 mmB.C 直径 0.15mm 0.15 直径 0.30 mm 0.30 mm刮伤(不得露出底材)A、B 长度 1mm且宽 0.05mm 长度1 2 mm且宽 0.05 mm 长度 2 mm或宽 0.05mm 长度 2mm且宽 0.05mm 长度2 5mm且宽 0.05 0.1mm 长度 5 mm或宽 0.1 mm备注1. 任何漏印气泡异色金属氧化物都不可接受不良数大于等于3个均拒绝。2. 两个不良项目的距离小于2cm拒收。3. 任何被标签遮盖的同色点异色点刮伤擦伤等不良不视为不良。
15、4. 检查卡勾及螺丝是否至定位,卡勾处不可损伤或缺料。4.Cosmetics (Non LCD & Keypad areas)Extra point with same colordiameter 0.2 mm diameter 0.15 mm d 0.25 mm, D d 0.30 mm diameter 0.20 d 0.30 d length 2mm and width 0.05mm length 2 5mm and width 0.05 0.1mm length 5 mm or width 0.1 mm1.Automatic rejection for no painting, bub
16、ble, discoloration, oxide for metal parts or total number of defects equal to or above 3.2.The distance between defects should be over 2cm.3.Any imperfection point and scratch which is located at the area where will be covered by Xcvr label or any other label will not be regarded as defect.4.Check t
17、he latches and screws for location,damage and parts missing.5. Color diference control : L1.0, a0.5, b0.5PhotoNoGap Spec(refer to PLT project)81 , 276Center of display pixels to the center of LCD lens transparent openingAcc : abs(a-b)/2) 0.2mmSkewness of LCD 0.2mm MaxMax(abs(A1-C1),abs(B1-D1)0.2mmMa
18、x(abs(A2-B2),abs(C2-D2)0.2mmGap from keypad to housingAcc: 0.3mm Max.Gap from key to key 0.3mm MaxGap from housing A to housing B 0.35mm Max.Gap from main lens to housing6.1Step between main lens and housing A Main lens higher than HousingA 0 mm Main Lens lower than Housing A 0.2mmGap from Hp name p
19、late to housingGap from Light lens to housing 0.2mm Max.8.1Step between Light lens and housingA Light lens higher than HousingA Light Lens lower than Housing A 0.2mm 1013912Gap from nameplate to battery coverGap from flash lens to nameplate11Gap from battery cover to antenna coverGap from flash lens
20、 to battery cover12.1Step between flash lens and namelate flash lens higher than nameplate flash lens lower than nameplate 0.2mm Gap from camera lens to nameplate1418171615Gap from battery cover to housing BGap from audio jack to housing BGap from micro USB to housing BGap from camera key to housing BGap from antenna cover to housing B20192122Gap form battery cover to housing AGap from knob to housing AGap from mute key to housing AGap from battery cover to knob23Gap from side key to housing B24Gap from antenna cover to housing A
copyright@ 2008-2022 冰豆网网站版权所有
经营许可证编号:鄂ICP备2022015515号-1