常用海上钻井英语500句Word下载.docx

1、接好冲桩管线，用7公斤/厘米2的压力开始冲桩。16、 The jetting pressure is 100 psi.冲桩压力7公斤/厘米2的压力。17、 According to the requirements wind speed less than force 3 and wave height less than 1 meter are considered as the optimum weather condition for the jacking down.按规定，要求风速在3级以下，波高小于1米是最佳的气象条件。MOVING A JACK UP RIG拖 航18、 Ther

2、e will be strong wind，we have to wait on weather.有强风，必须等候天气好转。19、 The wind speed is 1.5 meters per second and the wave height is less than 0.5 meter today Great！ 今天风速1.5米/秒，浪高小于半米，好极了！20、 Have you worked out the statistical list of variable loads?平台可变负荷统计表搞好没有？21、 Now the Rig is overloaded to the bo

3、at?现已超载，需要卸载?22、 What materials can be unloaded to the boat?哪些物品可以卸载到?23、 The surplus barite, bentonite and cement have to trans-fered to the supply boat.反多余的重晶石，粘土粉和水泥运到拖轮上。24、 The Rig is short of potable water. Tell the boat to come for transferring water to the Rig.平台生活用水缺乏，让拖轮靠平台打淡水。25、 Wheres t

4、he new location? What are the coordinates?交换机井位在什么地方？经纬度多少？26、 What is our position now?现在船位在哪里？27、 We have got the Rig position at 17:50 hours;10835EL （east longitude） and 2045NL （north latitude）.17时50分测得船位在：东经10835北纬2045。28、 Which tug is responsible for handling the anchors?哪条拖轮负责起抛锚。29、 Drop No.2

5、 and No.3 anchors, right?抛2号和3号锚，对不对？30、 When do we start jacking the Rig down?什么时候开始降船。31、 When do we going to start moving?什么时候开始拖航。32、 The move is supposed to start at eight thirty.预计8点半起拖。33、 Which one the main tug? The Binhai 281, it has 8,000HP（horse power）.主拖是哪条船？-滨海281，8000马力。34、 whats the m

6、oving speed now?现在船速多少？35、 About 4 knots.4节左右。36、 We can jack down the platform only when the wind scale is less than 4 and we have a smooth sea.四级风以下，海浪、海流不急时才可降船。37、 The speed has slowed down some because the fog is too thick.雾太大，航速成降低了些。38、 Which one is the chase boat? how much is the horse power

7、?护航船是哪一条？有多大马力？39、 Its the boat binhai 261. She has 6.000HP （horse power）.护航是滨海261船，6000马力。40、 What time will we get to the location.什么时候我们可以到达井位？41、 According to the present speed the Rig is expected to enter the location area at about 5 oclock tomorrow morning.按现在的航速，大约明早5时左右进入井位区。42、 The location

8、 buoy is in front over there. .前面就是井位标。43、 We are ready to drop the anchors.我们已经做好抛锚准备。44、 Everything is O.K.一切都正常。JACKING-UP AND PRELOADING升降及压载45、 Whats the air gap to start preloading?平台升离水面多少才开始压载？46、 We are not going to preload until the air gap gets to 3 meters.打算升三米再开始。47、 How much preload wa

9、ter will have to put into the tanks?压载舱内要加多少压载水？48、 Well have to put into 5500 tons of preload water.要加5500吨。49、 What way are you going to preload?打算如何压载？50、 We plan to have 3 steps for preloading. Each step will be followed by 30 minutes of observation. When the preloading finally finishes. There w

10、ill be 2 hours for observation.打算分三组压，每组压完观察30分钟，最后压完观察二小时。51、 Do we star preloading right now?现在开始压载吗？52、 well have to adjust the brake torque of jacking motors first so that the legs will jack evenly.先将升降马达的刹车扭矩调匀，这样桩腿升高比较平稳。53、 Can you get it done quickly?很快能调完吗？54、 It will probably take us one a

11、nd half hours to adjust the 36 motors.36个马达大概要1个半小时。55、 When the preloading finishes and nothing abnormal is found, then well be ready to drain the water off.压载完了。观察无变化，准备放水。56、 Why has the main engine stopped?主机为什么停机？57、 They are lowering the raw water tower（deep well pump）now, so only the emergenc

12、y generator can be operated.正在下放海水塔（深井泵），只能开应急发电机。58、 Let me check it ,O.K. penetrate the legs now.让我看一下，好，可以插桩了。59、 Check the leg penetration. How much penetration do we have?检查一下插桩情况，看看插下去多少 。60、 No.1 and No.2 legs indicate 10 meters and No.3 indicates 12 meters of penetration.1、2号桩腿插桩10米，3号桩腿插桩12

13、米。61、 Are the main generators back on the line ?主发电机并联好了吗？62、 O.K., continue to jack up the platform until we have an air gap of 12 meters.好吧，继续升降船，升到船离水面12米时停。Preperation before making hole钻前准备63、 Let the roustabouts unload the supply boat 201.叫甲板班卸201船。64、 Tell the mechanic to check the motor torq

14、ue.让机械师检查马达扭矩。65、 Set and fix the upper and lower wedges on the legs.将桩脚上、下楔块固定好。66、 The drilling crew is responsible to skid the derrick back to the drilling position.钻井班移动井架到工作位置。67、 Electrician must care of the electric cable moving whit derrick.电工注意照管好移动电缆。68、 Speed up. Please!请快点干！69、 Have you

15、fixed the derrick substructure in position?井架底座固定好没有？70、 Get all the drilling tools unlashed.解开所有钻具。71、 Put the ramp back onto the Vdoor 将坡板吊回到井架大门上。72、 Put the rathole scabbard back in place.安放大鼠洞。73、 Connect the Kelly spinner to the Kelly.连接动力短节和方钻杆74、 Connect the feeling plate to the drill collar

16、s.用钻铤连接探深板。75、 Have you checked all the equipments?设备都检查过了吗？76、 Weve checked them, no problems in running.检查过了，运转是没有问题了。77、 How much high viscosity mud move you mixed?高粘度泥浆配备了多少？78、 About 160 cubic meters.大约160方。79、 Please pick up the 171/2 bit and 36 hole opener to the floor.请将这个171/2钻头和36扩大器吊上钻台。8

17、0、 The distance between feeling plate and rotary table is 70 meters.探测海底到转盘面的深度是72米。INSTALLATION OF WELL HEAD ASSEMBLY AND PRESSURE TEST井口安装及测试81、 Cut off the 30conductor with the conch.用气焊割掉30隔水管。82、 Weld on the 30bottom flange.焊接30的底法兰。83、 Hoist and rig up the 30 Tee.吊装30三通。84、 Connect the 12 pneu

18、matic valve and the flow line.连接12气阀及管线。85、 Hoist and nipple up the 30diverter.转喷器。86、 Have the 30diverter pressure-tested with 1000psi.30转喷器试压1000磅/英寸2。87、 Rig up the 135/8 BOP stack onto the well head.将135/8防喷器组移到井口。88、 This gasket ring cant be used any more. Change to a new one, please.这个钢圈不能用了，换

19、个新的。89、 Tighten up the well-head guy-lines a bit-more.井口绷绳绷紧一些。90、 Change the 5 pipe rams to 31/2 rams.把这个5闸板换成31/2的。91、 Have the HYDRIL annular preventer pressure-tested to 5,000psi.海德里环形防喷器试压5000磅/英寸2。92、 Have the Camron type U BOP pressure-tested with 10,000psi.卡麦隆U型防喷器试压1000磅/英寸2。93、 Hold each p

20、ressure test for 10 minutes.每次试验稳压10分钟。94、 The pressure test is O.K.试压合格。95、 Have each valve of the stand-pipe manifold pressure-tested to 5.000psi.立管闸门逐个试压5000磅/英寸2。96、 Mud pumps arent allowed to be used for the test if the pressure is over 3000psi.超过000磅/英寸2的不允许直接用泥浆泵试压。97、 Run the wear bushing.下抗

21、磨补心。98、 Adjust the manifold pressure to 1500psi.管汇压力调到1500磅/英寸2。99、 Adjust the HYDRIL （annular preventer ） pressure to 900 psi.环形防喷器压力调到900磅/英寸2。100、 Close the blind ram, please.请关上防喷器盲板。101、 Open the pipe ram, please. 请打开闸板防喷器。102、 Check the pre-charged pressure of the accumulator.检查储能器预压。103、 The

22、accumulator pressure of the Koomey Unit is 3,000psi.库美系统储能压力3000磅/英寸2。BOTTOM HOLE ASSEMBLY井下钻具组合104、 Get a 121/4 Smith bit ready.准备一个121/4史密斯钻头。105、 Dont forget to put the TOTCO support ring in the bit sub （for the deviation survey.tool.）别忘了在钻头接头内安放测斜承托环。106、 The thread type of the bit is 6 5/8 regu

23、lar pin.钻头的扣型是6 5/8正规公扣。107、 Whats the make-up torque required for the bit?钻头上扣力矩要多大？108、 Run in two stands of 9 drill collars.下两根9钻铤。109、 Set the make-up torque of 9 DC to 10000 kg-meter.9钻铤上扣力矩要调到10000公斤米。110、 The cathead cant give enough torque, so we have to use a snatch block.猫头力量不够，要挂上滑轮。111、

24、Connect the 731630 crossover sub.接上731630的配合接头。112、 A 12 1/4 stabilizer is needed to be connected here.这个地方要接个12 1/4的扶正器。113、 This is a 7 3/4 flexible sub.这是7 3/4挠性短节。114、 Put the 8 jar on to the flexible sub.在挠性短节上接上8震击器。115、 A function test must be made before the jar is run in the hole.下震击器时，要做性能

25、试验。116、 Make up 15 joints of 5 HW Drill pipe.接上15根5加重钻杆。117、 The DIV （drop in valve） has to be put on top of the bottom two joints of HWDP.投入式止回阀安在下两根加重钻杆的上面。118、 This is the BHAbottom hole assembly log.这是井下钻具组合的记录本。119、 Make sure you record all outside and inside diameters and lengths in the.log 一定

26、要把所有的内外径和长度记好。120、 We need a short drill collar to put here.这里要接一根短钻铤。121、 Whet is the BHA of this well.这口井的钻具结构是什么？122、 This is the hole geometry of this well.这是这口井的井身结构。123、 The thread type of 9DS is 75/8Regregular.钻铤的扣型是75/8正规。OPERATING操 作124、 Latch the elevator.扣吊卡。125、 Unlatch the elevator.开吊卡。

27、126、 Set the slips around the pipe.放卡瓦。127、 Pull out the slips.提卡瓦。128、 Put out the slips.打大钳。129、 Adjust the crown-o-matic.调整防碰天车。130、 Put the Kelly into the rat-hole.方钻杆进鼠洞。131、 Lock the hook pin.锁紧大钩销子。132、 Pull the cat line.拉猫头。133、 Unlock the hook.打开大钩。134、 Operate the brake lever.扶刹把。135、 Stop the pumps for a flow check.停泵观察。136、 Make a wiper trip to the 20casing shoe.通井到20套管鞋。137、 Ream down all the tight points.