调试方案commissioning中英文双语版Word格式文档下载.docx

1、Installation of electrical equipment is completed. Laying of bridge, medium & low voltage cables and busbar is completed; wiring of secondary control cables is right as per drawings. Installation of power and lighting switchboard is completed; installation and wiring of power equipment are completed

2、; appearance check is qualified. Wiring of various lamps is completed. Wiring of various switch panels is completed.电气设备安装完毕。桥架及中、低压电缆、母线敷设完毕，二次控制电缆按图纸接线正确。动力、照明配电盘安装完毕，动力设备安装、接线完毕，外观检查合格。各种灯具接线完成，各种开关面板接线完毕。2HVAC system通风空调系统Stable power supply for air conditioning ventilating equipment, duct purgi

3、ng is qualified. Stable power supply for air conditioning water system, system flushing is qualified; hydraulic pressure of the system meets requirements; valve is turned on and turned off normally.空调风系统设备供电稳定，风管吹扫合格。空调水系统设备供电稳定，系统冲洗合格；系统水压满足要求，阀门启闭正常。3System of plumbing as well as fire fighting给排水及

4、消防系统Connection of equipment and pipeline is correct, it shall check completeness before equipment operates, hydraulic pressure test of pipe system and circulating flushing work of system have been completed.设备和管道连接准确，设备运行前应进行完整性检查，管道系统水压试验与系统循环清洗工作已经完毕。2. Organization measures of commissioning2、调试的组

5、织措施（1）Organization chart of commissioning is shown in the figure 3.14.1-2.（1）调试的组织机构见图3.14.1-2。Figure 3.14.1-2 Chart of commissioning organization 图3.14.1-2 调试组织机构图（2）Responsibilities of main personnel for project commissioning are shown in the table 3.14.1-2.（2）项目调试主要人员职责见表3.14.1-2。Table 3.14.1-2 R

6、esponsibilities of main personnel for project commissioning表3.14.1-2 项目调试主要人员职责No.序号Post职务Acting personnel担任人员Responsibilities职责Team leader组长Project manager项目经理Be responsible for establishment of commissioning organization, preparation of resources used in commissioning, establishment and implementa

7、tion of commissioning working system, coordination between MEP and other subcontractor at the stage of joint commissioning.负责调试机构的建立，调试需用资源的配备；负责调试工作制度的建立实施，联动调试阶段机电与其他分包间的协调。Deputy team leader副组长Technical director of the project项目技术负责人Be responsible for compilation and submission of organization co

8、mmissioning method statement, coordination and communication with related parties as well as management, coordination and cooperation in various commissioning work between the Owner ABB, Lend Lease Company and relevant director of the supervision unit and all other subcontractors; analyze and summar

9、ize commissioning result.负责组织调试方案的编制和报审，与外部相关方的协调与沟通，与业主ABB、联实公司及监理单位相关负责人和其他各分包单位各项调试工作的管理、协调与配合。对调试结果进行分析和技术总结。 Group leader of all disciplines专业小组长Professional engineer of commissioning调试专业工程师Be responsible for compilation of commissioning method statement and standard operation procedures for th

10、is area; safety and technical disclosure about commissioning work of this area; make solutions for difficult problems discovered in commissioning in the area of this discipline; ensure safety and reliability of instruments used in the commissioning of this area; implement the commissioning schedule

11、of the area, organizing to collate commissioning materials and issuing commissioning report. 负责本区域调试方案和作业指导书的编制；本专业本区域调试工作的安全、施工技术交底；负责本专业本区域调试过程中发现疑难问题的解决方案；负责本专业本区域调试所使用的仪器、仪表的安全和可靠性；负责本专业本区域调试进度计划的落实，组织整理调试资料并出具调试报告。4Group leader of resource guarantee资源保障小组长Material guarantee personnel物资保障人员Be re

12、sponsible for providing commissioning materials.负责提供调试所需物资。5Group leader of emergency handling应急处理小组长Professional engineer专业工程师Be responsible for handling emergencies occurred in the process of commissioning.负责调试过程中出现应急情况的处理。（3）Instrument and equipment used in commissioning are shown in “5.2 Guarant

13、ee measures for input of construction machinery equipment”.（3）调试所使用的仪器设备详见“7.2 施工机械设备投入保证措施”。3. Commissioning process is shown in the figure 3.14.1-3.3、调试流程见图3.14.1-3。Figure 3.14.1-3 Commissioning process chart图3.14.1-3 调试流程图3.14.2 Single-machine commissioning 3.14.2 单机调试1. Main contents and require

14、ments of single-machine commissioning of all disciplines are shown in the table 3.14.2-1.1、各专业单机调试的主要内容和要求见表3.14.2-1。Table 3.14.2-1 Contents and requirements of single-machine commissioning and system commissioning 表3.14.2-1 单机调试和系统调试内容和要求Name of discipline专业名称Contents of single-machine commissionin

15、g单机调试内容Commissioning requirements调试的要求Electrical system project电气系统工程power cable, low voltage breaker, meters, UPSs, current transformers, SPD, power/lighting distribution panels, AC motors.电力电缆、低压断路器、表、UPS、电流互感器、避雷器、动力/照明配电箱、交流电动机。Performances of electrical device meet requirements of design and pr

16、oduction process.电气装置的性能满足设计和生产工艺要求。Project of HVAC system空调通风系统工程Single-machine commissioning of air conditioning equipment （fan, air conditioning unit, water pump, FCU） and smoke control unit; balance of HVAC system, water balance of air conditioning water system; measurement of environmental temp

17、erature, humidity and noise; test of forced draft, blast capacity and wind pressure of smoke control system.空调设备（风机、空调机组、水泵、FCU）防排烟机组单机调试；空调风系统平衡、空调水系统水量平衡；环境温度、湿度、噪声测量；正压送风、防排烟系统风量、风压测试。Deviations of total blast capacity and water flow of air conditioning unit meet requirements of the specification

18、; indoor temperature, relative humidity and noise meet requirements of design and specifications.总风量、空调机组水流量偏差满足规范要求；室内温度、相对湿度及噪声满足设计及规范要求。Project of plumbing and fire fighting system给排水及消防系统工程Single machine commissioning of domestic water supply pump, fire pump and drainage pump; commissioning of w

19、ater supply system, drainage （rainwater） system and firefighting water system.生活给水泵、消防水泵、排水泵等设备单机调试；给水系统、排水（雨水） 系统、消防水系统调试。Flow and pressure of water supply and firefighting water system meet use requirements. Smooth drainage, non-leakage, installation of water pump and valve comply with requirement

20、s.给水、消防水系统流量及压力等满足使用要求，排水顺畅、无渗漏，水泵、水阀安装符合要求。2. Method of single-machine commissioning of main equipment:2、主要设备的单机调试方法：（1）Power cable: 1）measure insulating resistance; 2）DC voltage withstand test and measurement of leakage current; 3）AC voltage withstand test; 4）measure ratio of resistance of metalli

21、c shield layer and conductor resistance; 5）check phase positions of two ends of cable line; 6）cross interconnection system test.（1）电力电缆：1）测量绝缘电阻；2）直流耐压试验及泄漏电流测量；3）交流耐压试验；4）测量金属屏蔽层电阻和导体电阻比；5）检查电缆线路两端的相位；6）交叉互联系统试验。（2）Low voltage breaker: 2）breaking-closing test; 3） adjustment of switch setting values

22、.（2）低压断路器：1）测试绝缘电阻；2）分合闸试验；3）开关整定值的调整。（3）Meter: conduct precision calibration for instrument on the plate cabinet by using standard meter.（3）表：用标准表对盘柜上的仪表进行精度校验。（4）Current transformer: 1）measure insulating resistance of the winding; 2）check wiring group and polarity; 3）error measurement.（4）电流互感器：1）测

23、量绕组的绝缘电阻；2）检查接线组别和极性；3）误差测量。（5）SPD: commissioning as per technical specification of the manufacturer.（5）避雷器：按生产厂家技术说明进行调试。（6）Power/lighting switchboard:（6）动力/照明配电盘：1）Check insulation of switch and primary & secondary circuit in the power supply loop in the cabinet by using 1000V or 500V tramegger; i

24、nsulating resistance complies with requirements of the specification;1）采用1000V或500V兆欧表对箱内供电回路开关，一次、二次线路进行绝缘检查，绝缘电阻符合规范要求；2）Check air switch in the cabinet by using universal meter, whether its switching off and switching on are normal or not; check whether connection of primary circuit and secondary

25、 circuit complies with design requirements or not; whether the connection of wire, cable, guide line and terminal is solid or not.2）用万用表检查柜箱内空气开关，其开关分、合闸是否正常；检查一次、二次线路接线符合设计要求；电线、电缆、导线和端子连接是否紧固；3）Shall calibrate precision of amperemeter or voltmeter on the switchboard.3）应对配电盘上电流表或电压表进行精度校验。（7）AC mot

26、or: check of motor insulation, measure DC resistance of the winding; check the correctness of stator winding and its connection; check and test of control system of the motor; if it is normal through check, the motor shall be operated for two hours with no load; use thermodetector to measure tempera

27、ture of stator winding of the bearing of the motor, check whether the temperature rise in motor is normal or not. （7）交流电动机:电动机绝缘检查，绕组的直流电阻测量，检查定子绕组及其连接的正确性，电动机控制系统检查试验，检查正常后电动机空载运行2小时，用测温仪测量电动机轴承定子绕组等部位的温度，检查电机温升是否正常。（8）Fan: rotate the impeller by hands, observe whether there are jamming and collisi

28、on phenomenon or not; start fan, check whether there is friction, abnormal vibration and noise between impeller and enclosure or not; check whether rotating direction is consistent with the direction marked on the enclosure or not. After the fan operates stably, measure starting current, operation c

29、urrent, vibration, revolving speed, noise and bearing temperature of the fan;（8）风机：用手盘动叶轮，观察有无卡阻及碰擦现象；风机点动，检查叶轮与机壳有无摩擦、有无异常振动及声响；检查运转方向是否与机壳标注方向一致。风机启动运转平稳后，测量风机起动电流，运转电流、振动、转速、噪声及轴承温度。3.14.3 System commissioning 3.14.3 系统调试1. Commissioning of electrical system work1、电气系统工程的调试（1）Commissioning process of electrical system work（1）电气