美国钢铁标准文档格式.docx

1、Interior Fuel Gas Piping Systems Using Corrugated Stainless Steel Tubing ANSI/AGA LC-1a-1993 ANSI/AGA LC-1b-1994 ANSI/ASME A112.19.3M-1987 不锈钢卫生设备（家庭专用型） Stainless Steel Plumbing Fixtures （Designed for Residential Use） ANSI/ASME B36.19M-2004 不锈钢管 Stainless Steel Pipe ANSI/ASTM A193/A 193M-2001 高温设备用

2、合金钢和不锈钢螺栓材料规范 Specification for Alloy-Steel and Stainless Steel Bolting Materials for High-Temperature Service ANSI/ASTM A312/A 312M-2001 无缝和焊接奥氏体不锈钢管规范 Specification for Seamless and Welded Austenitic Stainless Steel Pipes ANSI/ASTM A480/A 480M-2001 平轧不锈钢及耐热钢板、薄板及带材一般要求规范 Specification for General

3、Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip ANSI/ASTM A688/A 688M-2001 奥氏体不锈钢焊接给水加热器管规范 Specification for Welded Austenitic Stainless Steel Feedwater Heater Tubes ANSI/ASTM A789/A 789M-2001 普通设备用无缝与焊接铁素体/奥氏体不锈钢管规范 Specification for Seamless and Welded Ferr

4、itic/Austenitic Stainless Steel Tubing for General Service ANSI/ASTM A814/A 814M-2001 冷加工焊接奥氏体不锈钢管规范 Specification for Cold-Worked Welded Austenitic Stainless Steel Pipe ANSI/ASTM A815/A 815M-2001 锻制铁素体、铁素体/奥氏体和马氏体不锈钢管配件规范 Specification for Wrought Ferritic, Ferritic/Austenitic, and Martensitic Stai

5、nless Steel Piping Fittings ANSI/ASTM A908-1996 不锈钢针管规范 Specification for Stainless Steel Needle Tubing ANSI/ASTM F2098-2004 保证SDR9交联聚乙烯（PEX）管用金属插件安全的不锈钢夹子的试验方法 Test Method for Stainless Steel Clamps for Securing SDR9 Cross-Linked Polyethylene （PEX） Tubing to Metal Insert Fittings ANSI/AWS A4.2M/A 4

6、.2-1997 奥氏体和双奥氏体-铁素体不锈钢焊接金属中铁酸盐含量测试磁仪器的校准程序 Calibrating Magnetic Instruments to Measure the Delta Ferrite Content of Austenitic and Duplex Austenitic-Ferrite Stainless Steel Weld Metal, Procedures for ANSI/AWS A5.22-2005 助溶剂芯弧焊用不锈钢焊条和钨电极惰性气体保护焊用不锈钢助溶剂芯焊条规范 Specification for Stainless Steel Electrode

7、s for Flux Cored Arc Welding and Stainless Steel Flux Cored Rods for Gas Tungsten Arc Welding ANSI/AWS B2.1-1/8-006-2002 在焊接条件下、有或没有垫板、10到18规格的碳钢与奥氏体不锈钢（M-1至M-18,或P-8）的气体保护金属极电弧焊 Gas Metal Arc Welding of Carbon Steel to Austentic Stainless Steel （M-1 to M-18, or P-8）, 10 through 18 Gage, in the as-W

8、elded Condition, with or without Backing ANSI/AWS B2.1-1/8-010-2002 在焊接条件下、有或没有垫板、10到18规格的碳钢与奥氏体不锈钢（M-1至M-18,或P-8）的钨电极惰性气体保护焊 Gas Tungsten Arc Welding of Carbon Steel to Austentic Stainless Steel （M-1 to M-8 or P-8）, 10 through 18 Gage, in the as-Welded Condition, with or without Backing ANSI/AWS B2

9、.1-1/8-014-2002 标准焊接程序规范.在焊接条件下、有或没有垫板、10到18规格的碳钢与奥氏体不锈钢（M-1至M-18,或P-8）的保护金 Standard Welding Procedure Specification - Shielded Metal Arc Welding of Carbon Steel to Austenitic Stainless Steel （M-1 to M-8 or P-8）, 10 through 18 Gage, in the as-Welded Condition, with or without Backing ANSI/AWS B2.1-1

10、/8-228-2002 碳钢与奥氏体不锈钢屏蔽金属电弧焊（从M-1/P-1/S-1,组1或组2焊接到M-8/P-8/S-8, 组1）1/8到1-1/2英寸厚,ER309 Welding Procedure Specification （WPS） for Shielded Metal Arc Welding of Carbon Steel to Austenitic Stainless Steel （M-1/P-1/S-1 Groups 1 and 2 Welded to M-8/P-8/S-8, Group 1） 1/8 through 1-1/2 inch thick, ER309-15,

11、16 or, 17, As-Welded Condition, Primarily Pipe Applications ANSI/AWS B2.1-1/8-229-2002 碳钢与奥氏体不锈钢气体钨电弧焊（从M-1/P-1/S-1,组1或组2焊接到M- 8/P-8/S-8, 组1）1/8到1-1/2英寸厚ER30 Welding Procedure Specification （WPS） for Gas Tungsten Arc Welding Followed by Carbon Steel to Austenitic Stainless Steel （M-1/P-1/S-1 Groups

12、1 and 2 Welded to M-8/P-8/S-8, Group 1） 1/8 through 1-1/2 inch thick, ER309 and E309-15, 16, or 17, As-Welded Condition, Primarily Pipe Applications ANSI/AWS B2.1-1/8-230-2002 气体保护钨极弧焊的标准焊接程序规范（WPS）,可熔嵌入根部的,碳钢与奥氏体不锈钢（M-1/P-1/S-1, 组 1 和 2 焊 Standard Welding Procedure Specification （WPS） for Gas Tungs

13、ten Arc Welding, with Consumable Insert Root, of Carbon Steel to Austenitic Stainless Steel （M-1/P-1/S-1, Groups 1 and 2 Welded to M-8/P-8/S-8, Group 1） 1/16 through 1-1/2 inch thick, IN309 and ER309, As-Welded Condition, Primarily Pipe Applications ANSI/AWS B2.1-1/8-231-2002 带可熔嵌入焊条的碳钢与奥氏体不锈钢气体保护钨电

14、弧焊（从M-1/P-1/S-1,组1或组2焊接到M- 8/P-8/S-8, 组1） Welding Procedure Specification （WPS） for Gas Tungsten Arc Welding, with Consumable Insert Root, Followed by Shielded Metal Arc Welding of Carbon Steel to Austenitic Stainless Steel （M-1/P-1/S-1, Groups 1 and 2 Welded to M-8/P-8/S-8, Group 1） 1/8 through 1-1

15、/2 inch thick, IN309, ER309, and E309-15, 16, or, 17, As-Welded Condition, Primarily Pipe Applications ANSI/AWS B2.1-8-005-2002 在焊接条件下、有或没有垫板、10到18规格的奥氏体不锈钢（M-8或P-8）的气体保护金属极电弧焊 Gas Metal Arc Welding of Austentic Stainless Steel （M-8 or P-8） 10 through 18 Gage, in the as-Welded Condition, with or wit

16、hout Backing ANSI/AWS B2.1-8-009-2002 在焊接条件下、有或没有垫板、10到18规格的不锈钢（M-8或P-8）的钨电极惰性气体保护焊 Gas Tungsten Arc Welding of Stainless Steel （M-8 or P-8）, 10 through 18 Gage, in the as-Welded Condition, with or without Backing ANSI/AWS B2.1-8-013-2002 标准焊接程序规范.在焊接条件下、有或没有垫板、10到18规格的奥氏体不锈钢（M-8/P-8）的保护金属电弧焊 Standa

17、rd Welding Procedure Specification - Shielded Metal Arc Welding of Austenitic - Stainless Steel （M-8/P-8）, 10 through 18 Gage, in the as-Welded Condition, with or without Backing ANSI/AWS B2.1-8-023-2005 在焊接条件下1/8到1-1/2英尺厚奥氏体不锈钢的保护金属电弧焊的标准焊接程序规范（WPS）（M-8/P-8/S-8,1组） Standard Welding Procedure Specif

18、ication （WPS） for Shielded Metal Arc Welding of Austenitic Stainless Steel （M-8/P-8/S-8, Group 1）, 1/8 through 1-1/2 inch Thick, As-Welded Condition ANSI/AWS B2.1-8-024-2001 在焊接条件下、1/8到1-1/2英寸厚的奥氏体不锈钢（M-8/P-8/S-8,组1）的钨电极惰性气体保护焊的焊接程序规范 （WP Welding Procedure Specification （WPS） for Gas Tungsten Arc We

19、lding of Austenitic Stainless Steel （M-8/P-8/S-8, Group 1）, 1/8 through 1-1/2 inch thick, As-Welded Condition ANSI/AWS B2.1-8-025-2001 在焊接条件下、保护金属电弧焊之后的1/8到1-1/2英寸厚的奥氏体不锈钢（M-8/P-8/S-8,组1）的钨电极惰性气体保 Welding Procedure Specification （WPS） for Gas Tungsten Arc Welding followed by Shielded Metal Arc Weldi

20、ng of Austenitic Stainless Steel （M-8/P-8/S-8, Group 1） 1/8 through 1-1/2 inch thick, As-Welded Condition ANSI/AWS B2.1-8-212-2001 主要用于管道的、在ERXX焊接条件下、1/8到1-1/2英寸厚的奥氏体不锈钢（M-8/P-8/S-8,组1）的钨电极惰性气体保 Standard Welding Procedure Specification （WPS） for Gas Tungsten Arc Welding of Austenitic Stainless Steel

21、 （M-8/P-8/S-8, Group）, 1/8 through 1-1/2 inch Thick ERXX, As-Welded Condition, Primarily Pipe Applications ANSI/AWS B2.1-8-213-1997 主要用于管道的、在焊接条件下（M-8/P-8/S-8,组）1/8到1-1/2英寸E3XX-XX奥氏体不锈钢的药皮焊条电弧焊的标准 Standard Welding Procedure Specification （WPS） for Shielded Metal Arc Welding of Austenitic Stainless S

22、teel （M-8/P-8/S-8, Group）, 1/8 through 1-1/2 inch Thick E3XX-XX, As-Welded Condition, Primarily Pipe Applications ANSI/AWS B2.1-8-214-2001 标准焊接程序规范（WPS）.主要用于管道的,在焊接条件下、1/8到1-1/2英寸厚ER3XX,E3XX-XX的奥氏体不锈钢 （M-8/P Standard Welding Procedure Specification （WPS） for Gas Tungsten Arc Welding Followed by Shie

23、lded Metal Arc Welding of Austenitic Stainless Steel （M-8/P-8/S-8, Group）, 1/8 through 1-1/2 Inch Thick ER3XX, E3XX-XX, As-Welded Condition, Primarily Pipe Applications ANSI/AWS B2.1-8-215-2001 在 IN3XX和ER3XX焊接条件下、1/8到1-1/2英寸厚的自耗嵌入式奥氏体不锈钢（M-8/P-8/S-8,组1）钨电极惰性气体保 Standard Welding Procedure Specificati

24、on （WPS） for Gas Tungsten Arc Welding, with Consumable Insert of Austenitic Stainless Steel （M-8/P-8/S-8, Group 1） 1/8 through 1-1/2 Inch Thick IN3XX and ER3XX, As-Welded Condition ANSI/AWS B2.1-8-216-2001 标准焊接程序规范（WPS）.焊接用, 1/8到1-1/2英寸厚IN3XX,ER3XX和E3XX-XX的奥氏体不锈钢（M-8/P-8/S-8,组1）的 Standard Welding Pr

25、ocedure Specification （WPS） for Gas Tungsten Arc Welding, with Consumable Insert Followed by Shielded Metal Arc Welding of Austenitic Stainless Steel （M-8/P-8/S-8, Group 1） 1/8 through 1-1/2 inch Thick IN3XX, ER3XX, and E3XX-XX, As-Welded Condition ANSI/AWS B2.1.009-1990 10至18号有或无背衬焊态条件下不锈钢（M-8或P-8）

26、钨极气弧焊接 ANSI/AWS B2.1.013-1991 在焊接条件下、有或没有垫板、10到18规格（M-8/P-8）奥氏体不锈钢的药皮焊条电弧焊的标准焊接程序规范（WPS） ANSI/AWS B2.1.014-1991 在焊接条件下、有或没有垫板、10到18规格（M-1到M-8/P-8）奥氏体不锈钢的药皮焊条电弧焊的标准焊接程序规范 （W Standard Welding Procedure Specification - Shielded Metal Arc Welding of Carbon Steel to Austenitic Stainless Steel （M-1 to M-8

27、 or P-8）, 10 through 18 Gage, in the as-Welded Condition, with or without Backing ANSI/AWS D1.6-1999 结构焊接代码.不锈钢 Structural Welding Code - Stainless Steel ANSI/AWS D10.4-1986 焊接奥氏体铬镍不锈钢管推荐惯例 Welding Austenitic Chromium-Nickel Stainless Steel Piping and Tubing, Recommended Practices for ANSI/AWS D18.1

28、-1999 卫生洁具用奥氏体不锈钢管和管道的焊接规范 Specification for Welding of Austenitic Stainless Steel Tube and Pipe Systems in Sanitary （Hygenic） Applications ANSI/AWS D18.2-1999 奥氏体不锈钢管内部焊接褪色度指南 Guide to Weld Discoloration Levels on Inside of Austenitic Stainless Steel Tube ANSI/AWWA C220-1998 4in（100mm）及以上尺寸的不锈钢管 St

29、ainless Steel Pipe 4 in （100 mm） and Larger ANSI/AWWA C220a-1999 不锈钢管.4英寸.（100 mm） 及更大. ANSI/AWWA C220a-98的附录 Stainless Steel Pipe, 4 In. （100 mm） and Larger, Addendum to ANSI/AWWA C220a-98 ANSI/AWWA C223-2002 结构钢和不锈钢开口套管 Fabricated Steel and Stainless Steel Tapping Sleeves ANSI/AWWA C561-2004 装配式不锈钢推拉门的AWWA标准 AWWA Standard for Fabricated Stainless Steel Slide Gates