LD电动单梁起重机说明书Word格式.docx

1、功率kW21.56转速r/min13807电动葫芦CD1（MD1）8起升高度Hm6、9、12、18、24、309起升速度V18（8/0.8）10运行速度V220（30）11工作级别A3A512电源3相 50Hz 380V13车轮直径mm27014轨道面宽377015跨度S7.58.59.510.511.512.513.514.515.51616.51719.522.5最大轮压PmaxkN1.081.311.091.321.101.331.121.351.131.361.141.371.151.391.161.401.171.411.181.421.211.451.231.471.241.481

2、.252.491.281.521.301.531.551.561.581.601.441.691.541.79最小轮压Pmin0.400.430.410.440.420.450.470.480.460.490.500.510.520.530.550.570.560.580.590.600.620.610.640.630.650.660.670.690.760.770.860.8718总质量1.672.141.722.241.762.281.822.341.862.381.912.431.962.482.012.532.052.572.102.622.192.712.762.292.812.33

3、2.852.442.962.503.022.543.062.593.112.643.162.703.223.633.534.0519基本尺寸H1490530580H3550595650710021H281086087022C279623C1127424W20002500300025B3500注：1起重机总质量包括电动葫芦质量；2起重机总质量和最大轮压按H=12m；3序号16，17，18三栏中上限数字为地面操作数据，下限为操纵室操作数据。表1续（一）LD2-D-LD2-S0.81.641.871.651.881.661.891.681.921.701.931.711.951.751.992.00

4、2.031.812.061.832.072.112.122.132.152.162.182.312.362.630.540.680.700.710.940.951.902.422.522.672.322.903.013.052.743.262.803.322.863.372.913.433.483.994.514.795.3166078570080090010001050106010801120871.51292.5 表1续（二） 型号LD3-D-LD3-S2.392.412.202.222.452.232.472.252.552.562.582.352.722.782.822.943.190

5、.740.780.790.800.820.810.830.851.021.202.402.172.693.083.142.733.253.313.093.913.414.003.554.073.624.143.704.223.794.314.434.955.415.93745820115011701185818.51291表1续（三）LD5-D-LD5-S3.283.513.293.523.303.333.563.353.583.363.603.613.723.503.743.773.573.813.593.833.683.923.943.733.963.983.764.013.784.034

6、.064.384.610.730.750.840.880.900.921.501.512.983.132.682.752.953.473.653.203.403.953.844.364.464.024.544.114.634.194.714.284.805.085.606.286.80520875720910101011001400141514401480841.51310表1续（四）60705.495.725.515.745.535.785.565.795.585.815.835.625.865.655.895.715.955.735.975.766.006.026.075.926.166.

7、195.986.226.246.036.056.306.576.606.850.720.890.930.970.981.001.273.394.214.293.824.394.084.604.374.895.005.225.135.255.235.355.505.845.946.066.276.156.377.217.438.238.45865111012101470149515401600164012304.安装图2-1 用于10t图2-2 用于1-54.1主横梁连接4.1.1在现场将起重机运行机构的驱动装置安装在横梁上。4.1.2按图2所示，将主横梁用螺栓连接起来，此螺栓为精制螺栓，其性能可保证主、横梁连接可靠，为更安全允许用户按图2在a、b、c处稍加间断施焊不宜焊得太满，以防变形。主、横梁组装后按标准JB/T1306-94中有关要求进行检验。主、横梁组装连接面应清理干净。4.1.3将起重机的行程开关及开关箱等电器组装到横梁上，接通电器，调试两个运行电机，使其转向一致。4.1.4电动葫芦可预先装在主梁上，同起重机一起架设到轨道上，也可以分别安装。4.1.5操纵室操作起重机。操纵室须在起重机架设到轨道之后，再组装到起重机上。4.1.6参照图3、图4架设电源滑触线装置。4.1.7按电