Drilling 钻井英语文档格式.docx

1、25. Move string during circulation. 在循环时注意活动钻具 26. Circulate hole clean. 循环清洗井眼 27. Circulate bottoms up. 循环泥浆几周 28. Fill up every 5 stands. 每5柱灌泥浆一次 29. Check mud weight every 15 minutes. 每15分钟检查泥浆比重 30. Reverse out excess cement. 反循环替出多余的泥浆 31. Change/replace old mud by new mud. 用新的泥浆替换出旧的泥浆 32. S

2、top drilling. 停止钻进 33. Drilling ahead. 钻进 34. Pull out of hole bit. 起出钻头 35. Change bit. 换钻头 36. Run the wear bushing. 下抗磨补心 37. The bit thread type is regular pin. 钻头丝扣是正规公扣 38. Whats the make-up torque? 上扣扭矩要多大? 39. Run in 9” collars. 下9”钻铤 40. The cathead cant give enough torque. 猫头力量不够 41. Conne

3、ct crossover sub. 接上配合接头 42. The tong angle is too small. 大钳的角度太小了 43. Stop circulating. 停止循环泥浆 44. Break out the stand. 卸立柱 45. Set the single into the mousehole. 把这个单根放进鼠洞 46. Can we break out the pipe with rotary table? 可用转盘卸扣吗?47. No! Break it out with tong. 不行! 要用大钳卸扣 48. Spin it out with the a

4、ir spanner. 用气动扳手卸扣 49. Put the pipe wiper on the string. 装上钻杆刮泥器 50. Dont set this stand back. 这根钻杆不要放在钻杆盒上 51. Make up the lift sub. 接好提升短节 52. Secure the safety clamp. 上紧安全卡瓦 53. The bit is nearing the shoe. 钻头快到套管鞋了 54. Slow down the running speed. 放慢下放速度 55. This is the undergauged interval. 这是

5、缩径井段 56. This is the drilling program. 这是钻井设计书 57. How much weight on bit is required? 要加多少钻压?58. Keep the rotary speed at 120-140 RPM. 转速保持120-140转/分 59. Keep the flow rate at 3000 LPM. 保持排量3000升/分 60. The pump pressure is too high. 泵压太高了 61. Dont ream the hole too fast. 划眼不要太快 62. Notice the rotar

6、y torque. 注意转盘扭矩的变化 63. The penetration rate is getting slower. 钻速变慢了 64. The bit is nearly worn out. 钻头快磨光了 65. Stop drilling at 2000 meters. 钻至2000米停钻 66. Circulate for one hour. 循环一个小时 67. The pump pressure has increased. 泵压升高了 68. One nozzle may be plugged. 可能有一个水眼（或: 喷嘴）堵了 69. What is the hook

7、load? 悬重多少?70. Whats the pick-up weight? 上提重量是多少?71. Whats the lowering weight? 下放重量是多少?72. Run in HWDP. 下加重钻杆 73. A stabilizer is needed here. 这里需要一个扶正器 74. This is a flexible sub. 这是挠性接头 75. This is the BHA log. 这是下部钻具组合记录 76. Record all outside and inside diameters. 记录好所有（入井工具的）内外径 77. We need a

8、short drill collar. 需要一根短钻铤 78. Pull the cat line. 拉猫头 79. Operate the break lever. 操作（或:扶）刹把 80. Stop the pumps. 停泵 81. Make a wiper trip. 通井 82. Retrieve wear bushing. 取出抗磨补心 83. Bleed off pressure. （释）放压（力） 84. Keep 5 wraps on the drum. 滚筒上留5圈 85. Set slips. 座上卡瓦 86. If tight hole, repeat wiper t

9、rip. 如果井眼紧, 重复划眼 87. Setback bottom hole assembly. 将下部钻具立于钻杆盒内 88. Make sure all alarms are on. 确保所有的警报信号都开着 89. Lay down TDS spinner. 拆下顶部驱动的旋扣器 90. Run in hole bit #15 to bottom. 用15号钻头下钻到井底 91. Run in hole to casing shoe. 下钻至套管鞋 92. Pick up same bit and BHA. 装上同样的钻头和钻具组合 93. Lay down 5” HW drill

10、pipe. 甩5”加重钻杆 94. Move string every 2 hours. 每2小时活动钻具一次 95. Keep area around shaker clean. 保持振动筛区域干净 96. Control trip gas. 控制起下钻气 97. Ream if needed. 如必要时进行划眼 98. Select the best penetration rate. 选择最佳钻进速度 99. Fix the traveling assembly. 固定游动系统100. 100. Check power tongs and spinning rope are on dri

11、ll floor. 检查动力钳和尾绳是否在钻台100. Whats the weight on bit? 钻压是多少?101. What is the BHA of this well? 这口井的下部钻具如何组合?102. Drill out cement. 钻穿水泥 103. Drill out 20” casing shoe. 钻穿20”套管鞋 104. Latch the elevator. 扣吊卡 105. Unlatch the elevator. 开吊卡 106. Set the slips. 放卡瓦 107. Adjust the crown-o-matic （crown sav

12、er）. 调整防碰天车 108. Lock the hook pin. 锁紧大钩销子 109. Check OD of stabilizer. 检查扶正器的外径 110. Perform leak off test. 进行地层破裂（或:渗漏）测试 111. Connect kill and choke line. 接上压井和放喷管线 112. Reverse out the drill pipe. 反循环清洗钻杆 113. Make a short trip. 进行短途起下钻 114. Change the cutters. 换割刀 115. Slug the pipe. 灌重泥浆 116.

13、Drill the stand down. 钻完立柱 117. Start/run the shale shaker. 开振动筛 118. Start the desanders. 开除砂器 119. Start the desilters. 开除泥器 120. Change it with a 40 mesh screen. 换成40目筛布 121. Shut it off. 关掉 122. Pull it to the cat ramp. 把它拉到坡道上去 123. Make a fast connection. 接单根要快 124. Dont dump the mud into the

14、sea. 不要把泥浆排放到海里 125. Disconnect it with a chain tong. 用链钳卸开 126. Put a thread protector. 加一个（丝扣）护箍 127. Can we use the power slips? 可以使用动力卡瓦吗?Casing and Cementing 下套管与固井 128. Run in hole to bottom for wiper trip. 下钻通井 129. This is the casing program. 这是套管程序 130. Prepare for running casing. 准备下套管 131

15、. Make everything ready for running 7”casing. 做好下7”套管的准备 132. Make cementing job. 固井 133. Displace cementing with mud pump. 用泥浆泵替泥浆 134. Set cement plug from 2940 to 2790m. 在2940到2790米井段打水泥塞 135. Pick up cementing head. 接水泥头 136. Cement samples are hard. 水泥样已凝固 137. Pump in 3 cubic meters of spacer.

16、 注3方隔离液 138. Pump down the plug. 泵压（胶）塞 139. Wait on cement. 候凝 140. The guide shoe will be connected. 接引鞋 141. Connect the floor collar. 接浮箍 142. Connect the air line to the casing stabbing board. 接好套管 扶正台的气管线 143. Run casing with the 350T slip elevator. 用350吨卡瓦式吊卡下套管 144. Clean and dry 20” casing

17、threads with rags. 清洁并擦干20”套管丝扣 145. Where is the rabbit for drifting the casing? 套管通径规在哪里?Rig Move, Anchoring and Positioning 拖航, 抛锚, 定位146. What is our position now? 我们现在船位在哪里?147. Whats the moving speed now? （Whats the towering speed?） 拖航速度是多少?148. The speed is about 4 knots. 船速是4节左右 149. Which o

18、ne is the main tug? 主拖是哪条船?150. The main tug is Nanhai 205. 主拖是南海205 151. Which one is the chase boat? 护航船是哪一条?152. How much is the horse power? 有多大马力?153. She has 6000 HP. 有6000马力 154. Move the rig off location 50 feet. 将平台移开50英尺 155. We are ready to drop the anchor. 我们已经做好抛锚的准备了 156. Secure all th

19、e movable equipment. 固定好各种活动的设备 157. Preload. （自升式）压载 158. Ballast. （半潜式）压载 159. Put the preload water into the tank. 向压载舱灌压压载水 160. We need 5500 tons of preload water. 需要5500吨压载水 161. Shall we preload right now? 马上开始压载吗?162. Drain the water off. 放水 163. The rig is overloaded. 平台已超载 164. Jack up （ja

20、ck down） the rig. 升（降）船 165. The draft is 3.5 meters. 船体吃水3.5米 166. The jetting pressure is 100psi. 冲桩压力是100psi 167. Penetrate the legs. 插桩 168. How much penetration do we have? 入泥多深了?169. No.1 and No.2 legs indicate 10 meters. 1,2号桩腿插入10米 170. Fix the upper and lower wedges. 固定上下楔块 171. Pay out the

21、 anchor line. 放出锚缆绳 172. Skid the derrick. 移开井架 173. The rig is short of potable water now. 平台缺乏饮用水 174. Drop No.2 and No.3 anchors. 抛2号和3号锚 175. Why has the main engine stopped? 主机为什么停?176. Unleash the drilling tools. 卸开钻具 177. Tighten up. 绷紧（或:上紧）一点 178. Turn on the cooling water for the windlasse

22、s. 开锚机刹车冷却水 179. Retrieve the No.1 to No.8 anchors. 起1到8号锚 180. Check the paint marks at the anchor winches. 检查锚机上的油漆记号 181. Prepare for a location move. 准备好移井位 182. Commence anchor handling. 开始起锚（或抛锚） 183. Secure all equipment stored on deck. 固定好所有存放在甲板上的设备 184. Carry out stability and load calcula

23、tions. 做稳性和载荷计算 185. Pass pendant line, shackle and buoy to anchor handling vessel. 将起抛锚短索, 卸扣和浮标吊起给起锚船 186. Lower the windward anchor to seafloor. 抛上风锚到海底 187. Pick up the leeward anchor first. 先起下风锚 188. Take anchor chaser （or chaser） back to rig. 将捞/抛锚环送回平台 189. Hook up towing lines to tug boat.

24、将拖缆连接到拖轮 190. Sound fog signal for two seconds every twenty seconds. 发大雾信号, 每20秒钟响两秒Fishing 打捞 191. The bit cutters have been lost in the hole. 牙轮落井 192. Run in the reverse-circulation basket. 下反循环打捞篮 193. There is a lot of junk in the hole. 井下有很多落物 194. The fish is 235.46 meters long. 落鱼长度235.46米 1

25、95. The fish top is at 2478.34 meters. 鱼顶位置2478.34米Coring 取芯 196. Stop drilling for coring. 停钻准备取芯 197. Make up core bit. 接取芯钻头 198. What type of core bit is it? 这是什么 型号的取芯钻头?199. Run in a diamond core bit. 下金刚石取芯钻头 200. Lets drop the ball for coring. 可以投球取芯 201. The core has been broken off. 岩芯断了 2

26、02. Put the core in the boxes. 把岩芯装在岩芯盒里 203. Dont brake suddenly. 不要猛刹车 204. Take out the core. 岩芯出筒 205. How long is the core? 岩芯多长 206. The core recovery is 98%. 岩芯收获率是98% 207. Run in the core barrel again. 继续下岩芯筒（或: 取芯筒） 208. Run in hole core barrel. 下取芯筒 209. Drop ball. 投钢球 210. Recover core. 取

27、出岩芯 211. Use same parameters as for core #1. 使用与1#取芯同样的参数Freeing Stuck Pipe 卡钻与解卡 212. The down-hole problems are very complicated. 井下情况很复杂 213. The hole is tight. 遇阻了 214. Overpull while tripping out. 起钻遇卡（overpull: 超拉力） 215. The formation is unstable. 地层不稳定 216. The wall caving is severe. 井壁垮塌严重 2

28、17. There are many return cuttings. 返出岩屑特别多 218. The mud returns have decreased. 返出泥浆减少 219. The hole is enlarged. 井眼扩大了 220. The pipes stuck. 卡钻了 221. Pull up to 150 tons. 上提150吨 222. Slack off to 50 tons. 下放至50吨 223. Ream down all the tight points. 在所有遇阻点进行划眼 224. The rotary table cant rotate. 转盘转不动 225. Where is the sticking point? 卡点在哪里 226. Ma