无损检测NDE检测报告表格中英对照精编版Word文档下载推荐.docx

1、Type of ray source / equipment tag No胶片类型：Film type焦距：Focal distancemm胶片规格：Film specification管电压/同位素类型：Tube voltage / isotope typekV增感方式：Increased sensitivity mode管电流/活度：Current / activitymA/Ci像质计型号： IQI type曝光时间：Exposure times像质指数：Image quality indicator透照方式：Exposure method黑度：Darkness拍 片 数 量Quantit

2、y总计：Total张Pieces其中：一次返修Of which: 1st repair 张 二次返修Pcs 2nd repair张 三次返修Pcs 3rd repairPcs扩透Additional pictures taken评 定 结 果Results级Class I张 级Pieces Class II级Class III张 级Pieces Class IV备 注Remarks1 检测部位见附图 See the attached sketch for examination positions.，检测结果见射线检测报告（二）。See “Radiographic Inspection Rep

3、ort （II）” for examination results.检测人：Examined by 年（Y）月（M）日（D）审核人：Reviewed by年（Y）月（M）日（D）（检验专用章）Special examination stampSH 3503J123-2射线检测报告（二）Radiographic Examination Report （II）工程名称 Project description：第Page页 共Total页Page工程类别 Project category：Installation Unit底 片 编 号Film No透照日期Date picture taken缺陷性

4、质Defect nature缺陷尺寸（mm）Defect size评定结果Evaluation result布片图号Films arrangement drawing缺陷性质 Defect nature： C=Crack裂纹， P=Porosity圆形气孔， WP=Worm Porosity长形气孔， SI=Slag Inclusion 夹渣， IF = Incomplete Fusion未融合， IP = Incomplete Penetration未焊透， UC = Undercut咬边Reviewed by SH 3503J124超声波检测报告Ultrasonic Examination

5、 Report工程名称 Project Description：单元名称 Unit Description：第page页 共Total页Pages工程类别 Project Category：检件名称报 告 编 号检件规格Work piece specification检 件 材 质执行标准检 验 比 例Inspection rateQualification class检件总量Total Work pieces检测数量Number of Work pieces tested检件类型Work piece type检验时机Test time表面状况Surface condition仪器型号Appa

6、ratus type探测波型Wave type耦 合 剂Bounding agent探头型号Probe type探头K值K value of probe补 偿Compensation标准试块Standard test block探测灵敏度Sensitivity抑 制Suppression灵敏度试块Sensitivity test block扫描线调整方式Scanning line adjustment mode探头扫查方式Probe scanning mode检测部位（编号）Inspection position （Number）厚 度Thickness检 测 结 果Inspection re

7、sultsRemark缺陷尺寸（数量）Defect size （quantity）评定级别Evaluated class评定结论Evaluation conclusion缺陷及返修情况说明：Explanation on defects and repairs Inspected byApproved bySpecial inspection stampSH 3503J124-F超声波检测报告（续表）Ultrasonic Examination Report （Continued） 第页共页Work piece NumberInspection position （number）Defect s

8、ize （Quantity）SH 3503J125超声波测厚报告Ultrasonic Thickness Measurement Report表面状态Surface statusTested quantity工件编号Work piece number测点编号Measuring point number公称厚度Nominal thickness实测厚度Measured thicknessMeasuring thickness检测结论Inspection conclusion检测部位示意图：Inspection positions diagramInspected byInspection spe

9、cial stampSH 3503J126磁粉检测报告Magnetic Particle Examination Report第Page 页 共Total 页pagesInspection time检测比例电流类型Current type检验方法Inspection method磁化方式Magnetization mode提 升 力Lifting force磁极间距Distance between poles磁化方向Magnetization direction磁粉种类Magnetic particle type悬 浮 剂Suspension agent磁化时间Magnetization ti

10、me磁悬液浓度Concentration灵敏度试片Sensitivity Work pieceInspection location （number）Defect sizesConclusionExplanations on defects and repairsTested byApproved by SH 3503J126-F磁粉检测报告（续表）Magnetic Particle Examination Report （Continued）第Page页 共Total 页PagesTest position （No）Evaluation classExamined by:Reviewed b

11、y:SH 3503J127渗透检测报告Penetration Test Report 第（page No）页 共（total） 页（pages）检测时机检测温度Test temperatureTest rate检 验 材 料Test materials牌 号Brand类 型Type渗 透 剂Penetrative agent清 洗 剂Detergent显 像 剂Developer检 测 部 位Test position检 测 结 果Results缺陷及返修情况说明Explanations on defects and repairs：Tested by:Approved by:SH 3503J127-F渗透检测报告（续表）Penetration Test Report第（page No）页 共（Total）页（pages）Test Result