1、Approved as ANSI /UL 1414 1978,July 17 1978Approved as ANSI /UL1414 1983 ,March 17 ,1983Approved as ANSI /UL 1414 1988,October 6,1988Approved as ANSI /UL 1414-1994 February 14,1994Revisions of this standard will be made by issued revised or additional pages bearing their date of issue .A UL Standard
2、 is current only if it incorporates the most recently adopted revision, all of which are itemized on the transmittal notice that accompanies the latest published set of revision pagesISBN 1-55989-570-5 Copyright 19751994 UNDERWRITERS LABORTORIES INC.CONTENTSFOREWORD INTRODUCTION 1 SCOPE5 2 Terminolo
3、gy 5 3 Glossary5 4 Reference.5 5 Units of Measurement.5CONSTRUCTION 6 Enclosure .6 7 Sleeving ,Tape ,Tubling and wire insulation6 8 Spacings6PERFORMANCE ALL CAPACITORS 9 Capacitor Flammability Test.8 10 Dielectric Voltage-withstand Test .8ANTENNA- COUPLING CAPACITOR 11General 9ACROSS-THE-LINE CAPACI
4、TOR 12 General9 13 Discharge test .9 14 Life test .13LINE-BY-PASS CAPACITOR 15 General .14 16 Discharge test14 17 Life test .16DOUBLE-PROTECTION CAPACITORS 18 General .16 19 Across-the-line discharge test16 20 Across- the- line life test.17 21 Antenna-coupling discharge test 18 22 Antenna-coupling l
5、ife test.19MANUFACTURING AND PRODUCTION TESTS 23Dielectric Voltage-withstand.19 24 Capacity measurement.22MARKING 25 Details.22FOREWORDA. This standard contains basic requirements for products covered by UL under its Follow-Up service for this category with the limitations given below and in the sco
6、pe section of this standard .These requirements are based upon sound engineering principles, research ,records of test and field experience ,and an appreciation of the problems of manufacture,installation,and use derived from consultation with and information obtained from manufactures, users,inspec
7、tion authorities ,and other having specialized experience.They are subject to revision as further experience and investigation may show is necessary or desirable. B. The observance of the requirements of this Standard by a manufacturer is one of the condition of the continued coverage of the manufac
8、turers product.C. A product which complies with the text of this Standard will not necessary be judged to comply with the Standard if ,when examined and tested ,it is found to have other features which impair the level of safety contemplated by these requirements.D. A product employing materials or
9、having forms of construction differing from those detailed in the requirement of this standard may be examined and tested according to the intent of the requirement and ,if found to be substantially equivalent, may be judged to comply with the Standard.E. UL. In performing its functions inaccordance
10、 with its objectives ,does not assume or undertake to discharge any responsibility of the manufacturer or any other party. The opinions and findings of UL represent its professional judgment given with due consideration to the necessary limitations of practical operation and state of the art at the
11、time the standard is processes. UL shall not be responsible to anyone for the use of or reliance upon this Standard by anyone. UL shall not incur any obligation or liability for damages ,including consequential damages ,arising out of or in connection with the use,interpretation of or reliance upon
12、this Standard.F. Many tests required by the standard of UL are inherently hazardous and adequate safeguards for personnel and property shall be employed in conducting such tests.1 Scope 1.1 These requirements cover capacitors rated not more than 1.0 microfarad,85 250 voltages,and 60hertz that are em
13、ployed in radio ,television receiving,and similar appliance circuit where breakdown of the capacitor may result in a risk of fire ,electic shock ,or injury to persons. 1.2 These requirements also cover double protection capacitors rated more than 1.0 microfarad,85,125Voltages,and 60 hertz that are e
14、mployed in video ,television receiving,and similar appliance circuits where breakdown of the capacitor may result in a risk of fire ,electic shock ,or injury to persons. 1.3 A product that contains features characteristics, components,materials or systems new or diffient from those in use when the s
15、tandard was developed ,and that involves a risk of fire electric rock,or injury to person shall be evaluated using the appropriate additional component and end- product requirements as detemined necessary to maintain the level of safety for the user of the product as originally anticipated by the in
16、tent of this Standard.2 Terminology 2.1 For the purpose of these requirements ,the term capacitor also refers to combinations of capacitor and resistors.3 Glossary 3.1 ACROSS-THE LINE CAPACITOR- A capacitor that is connected either across a supply circuit or between one side of a supply circuit and
17、conductive part that may be connected to the earth ground. 3.2 Antenna-coupling capacitor A capacitor that is connected from an antenna terminal to circuit within an appliance. 3.3 Double-protection capacitor A capacitor that provides protection against the risk of electric shock in accordance with
18、the requirements for double protection in the standard for television receivers and high-voltage video produce,UL1410. 3.4 LINE-BY-PASS CAPACITOR A capacitor that is connected between one side of a supply circuit and an accessible conductive part.4 references 4.1 Any undated reference to a code or s
19、tandard appearing in the requirements of this standard shall be interpreted as referring to the latest edition of that code or standard5.Units of measurement5.1 If a value for measurement is followed by a value in other units in parentheses ,the second value may be only approximate.The first state v
20、alue is the requirement.6 Enclosure6.1 A nonmetallic material used as all or part of the enclosure of a capacitor shall either: a) Be classified 94V-0 as the determined by the test described in the standard for test for flammability of plastic Materials for parts in devices and appliances,UL 94, orb
21、) Perform acceptably when tested in accordance with capacitor flammability test, section9. 6.2 A material classified 94V-0 or better using 1/16-inch (1.6mm)thick flat-stock samples may be used in lesser thickness7 Sleeving ,Tape, Tuping and Wire insulation 7.1 Sleeving ,tape,tubing and wire insulati
22、on shall be rated for the voltage involved and the temperature attained under any condition of actual use.Tape shall be flame-retardant .Sleeving ,tubing,and wire insulation shall have a flame retardant rating VW-18 Spacings 8.1 General 8.1.1 The spacing between uninsulated live parts of opposite po
23、larity,and between an uninsulated live part and a dead metal part ,shall not be less than the applicable value specified in table 8.1 Table 8.1 spacingsCapacitor rating voltsMinimum spacing through air and over surface ,inch(mm)125 or less 1/16(1.6)125 to 2501/8(3.2) 8.2 Double-protection capacitor
24、8.2.1 The spacing between uninsulated live parts of opposite polarity,and an uninsulation live part and a dead metal part shall not be less than 1/8inch(3.2mm) over surface or through air . 8.2.2 The spacing between uninsulationed live part of the same polarity but of a different potential shall not
25、 be less than 1/16inch(1.6mm) over surface or through air, see figure 8.1.Figure8.1Polaritles in double-protection capacitorsleaderEnlosureDCBAFor the purpose of judging spacings in doule-protection capacitors:a) Capacitor elements A and D are considered to be at opposite polarity and b) Capacitor e
26、lements A and B ,C and D ,A and C,and B and D are considered to be at different potiential but of the same polarity.PERFORMANCE9 Capacitor Flammability Test 9.1 IF a nonmetallic capacitor enclosure material is not classified 94V-0 ,three samples of the capacitor shall be subjected to three 15 -secon
27、d applications of a test flame,the period between applications of the flame being 15 seconds.The material of the enclosure is acceptable if each capacitor does not continue to flame for more than 15 seconds after the first and second applications, and for not more than 60 seconds after the third app
28、lication . 9.2 For the test required by 9.1,a supply of gas having heating value of approximately 1000 btu per cubic foot(37.6MJ/m3 ) at normal pressure and 3/8 inch (9.5mm)diameter thrill burner are to be used. The test flame is to be 3/4 inch (19mm) high with air ports of the burner closed. 9.3 Ea
29、ch capacitor is to be mounted in a position that is most conductive to the ignition of the capacitor and which is permitted by the physical condstruction of the capacitor .The tip of the test flame is to be applied at any location on the body of each capacitor. 10 Dielectric Voltage-withstand test 1
30、0.1 As received samples10.1.1 Ten capacitors shall withstand without indication of unacceptable performance for 1 minute a sinusoidal potential,having a frequency of 60 hertz,applied from lead to lead .The potential shall be 1250 volts rms for capacitors rated up to 125 volts, and 1500 Vrms for capacitors rated 126250 v
copyright@ 2008-2022 冰豆网网站版权所有
经营许可证编号:鄂ICP备2022015515号-1