DHT11数字温湿度传感器附1602显示程序已验证ok.docx

1、DHT11数字温湿度传感器附1602显示程序已验证okDHT11数字温湿度传感器(附1602显示程序)已验证okD7、DHT11引脚说明 8、DHT11温湿度1602液晶显示程序示例主程序：#include #include #include #include#includetypedef unsigned char U8; typedef unsigned int U16; U8 U8FLAG;U8 U8count,U8temp;U8 U8T_data_H,U8T_data_L,U8RH_data_H,U8RH_data_L,U8checkdata;U8 U8T_data_H_temp,U8

2、T_data_L_temp,U8RH_data_H_temp,U8RH_data_L_temp,U8checkdata_temp;U8 U8comdata;sbit P2_0 = P20 ;sbit P2_1 = P21 ;sbit P2_2 = P22 ;sbit P2_3 = P23 ;unsigned char str1=ShiDu:;unsigned char str2=WenDu:;void Delay(U16 j) U8 i; for(;j0;j-) for(i=0;i27;i+); void Delay_10us(void) U8 i; i-; i-; i-; i-; i-; i

3、-; void COM(void) U8 i; for(i=0;i8;i+) U8FLAG=2; /- P2_1=0 ; /T P2_1=1 ; /T /- while(!P2_0)&U8FLAG+); Delay_10us(); Delay_10us(); / Delay_10us(); U8temp=0; if(P2_0)U8temp=1; U8FLAG=2; while(P2_0)&U8FLAG+); /- P2_1=0 ; /T P2_1=1 ; /T /- /超时则跳出for循环 if(U8FLAG=1)break; /判断数据位是0还是1 / 如果高电平高过预定0高电平值则数据位为

4、 1 U8comdata=1; U8comdata|=U8temp; /0 /rof /-/-湿度读取子程序 -/-/-以下变量均为全局变量-/-温度高8位= U8T_data_H-/-温度低8位= U8T_data_L-/-湿度高8位= U8RH_data_H-/-湿度低8位= U8RH_data_L-/-校验 8位 = U8checkdata-/-调用相关子程序如下-/- Delay();, Delay_10us();,COM(); /-void RH(void) /主机拉低18ms P2_0=0; Delay(180); P2_0=1;/总线由上拉电阻拉高 主机延时20us Delay_

5、10us(); Delay_10us(); Delay_10us(); Delay_10us();/主机设为输入 判断从机响应信号 P2_0=1;/判断从机是否有低电平响应信号 如不响应则跳出，响应则向下运行 if(!P2_0) /T ! U8FLAG=2;/判断从机是否发出 80us 的低电平响应信号是否结束 while(!P2_0)&U8FLAG+); U8FLAG=2;/判断从机是否发出 80us 的高电平，如发出则进入数据接收状态 while(P2_0)&U8FLAG+);/数据接收状态 COM(); U8RH_data_H_temp=U8comdata; COM(); U8RH_da

6、ta_L_temp=U8comdata; COM(); U8T_data_H_temp=U8comdata; COM(); U8T_data_L_temp=U8comdata; COM(); U8checkdata_temp=U8comdata; P2_0=1;/数据校验 U8temp=(U8T_data_H_temp+U8T_data_L_temp+U8RH_data_H_temp+U8RH_data_L_temp); if(U8temp=U8checkdata_temp) U8RH_data_H=U8RH_data_H_temp; U8RH_data_L=U8RH_data_L_temp;

7、 U8T_data_H=U8T_data_H_temp; U8T_data_L=U8T_data_L_temp; U8checkdata=U8checkdata_temp; /fi /fivoid main()U8 shidu_shi,shidu_ge,wendu_shi,wendu_ge; LCD_init(); delay_nms(2); LCD_write_string(0,LINE1,str1); LCD_write_string(0,LINE2,str2); while(1) RH(); shidu_shi=0x30+U8RH_data_H/10; shidu_ge=0x30+U8R

8、H_data_H%10; / shidu_xs=0x30+U8RH_data_L/10; wendu_shi=0x30+U8T_data_H/10; wendu_ge=0x30+U8T_data_H%10; /wendu_xs=0x30+U8T_data_L/10; LCD_write_char(6,0,shidu_shi); LCD_write_char(7,0,shidu_ge); /LCD_write_char(9,0,shidu_xs); LCD_write_char(6,1,wendu_shi); LCD_write_char(7,1,wendu_ge); /LCD_write_ch

9、ar(9,1,wendu_xs); H 文件 ifndef lcd_H#define lcd_H#include #include /*/common part #define HIGH 1#define LOW 0#define TRUE 1#define FALSE 0#define ZERO 0 #define MSB 0x80#define LSB 0x01/*/lcd part#define LINE1 0#define LINE2 1#define LINE1_HEAD 0x80#define LINE2_HEAD 0xC0#define DATA_MODE 0x38#define

10、 OPEN_SCREEN 0x0C#define DISPLAY_ADDRESS 0x80#define CLEARSCREEN LCD_en_com(0x01)/*/change this part at different board#define LCDIO P1sbit LCD1602_RS=P24; sbit LCD1602_RW=P25; sbit LCD1602_EN=P26; /*/void LCD_Read_BF(void)unsigned char read=0; LCD1602_RS = LOW; /RS 0LCD1602_RW = HIGH; /RW 1LCD1602_EN = HIGH; /EN 1 Read BFLCDIO = 0xFF;do read = LCDIO;while(read&MSB);void LCD_en_com(unsigned char command) /写指令LCD_Read_BF(); LCD1602_RS = LOW; /RS 0 LCD1602_RW = LOW; /RW 0 LCD1602_EN = HIGH; /EN -|/_ Write commandLCDIO = command;LCD1602_EN = LOW;void LCD_en_dat(unsigned cha