1、所有关系到安全的功能都将被测试,确保治疗安全进行。治疗开始前不可跳过自检。仅在自检程序完全通过后开始治疗程序才是安全可靠的。3Authors:Guenter NissenHeiko RiemenschneiderTraining document,no update service.This document may not be copied,partly or whole,or made be accessible to third parties without our permission and remains the property of B.Braun Medizintechn
2、ologie GmbH with all rights.27/10/2022安全第一安全第一 -自检程序步骤自检程序步骤1.开机后开机后软件和定标数据检查软件和定标数据检查 上次消毒记录检查上次消毒记录检查2.治疗前自检治疗前自检safety system安全报警系统安全报警系统internal hydraulic进水进水 blood leak漏血传感器漏血传感器 Heater加热器加热器Temperature温度传感器温度传感器Conductivity电导度传感器电导度传感器Ultrafiltration超滤部分超滤部分SAD空气传感器空气传感器pressure sensors血路压力血路压
3、力4.消毒冲洗消毒冲洗消毒:温度、浓度达到要求消毒:温度、浓度达到要求+冲洗冲洗ok3.治疗 同时传感器不间断的监测并由独立的监测系统处理器计算报警临界值自动或 手动开机 4Authors:Guenter NissenHeiko RiemenschneiderTraining document,no update service.This document may not be copied,partly or whole,or made be accessible to third parties without our permission and remains the property
4、 of B.Braun Medizintechnologie GmbH with all rights.27/10/2022开机初始化开机初始化开机信号发送到SMPSLLC初始化硬件装载程序装载定标数据LLS初始化硬件装载程序装载定标数据启动 Diabus通讯检查检测板开关K1位置 0-2-3启动与开关位置相应的程序 Therapy-TSM-Software Update报警信息:RAM/ROM Error 或 CRC calibration Error 如果自检失败 TLC主板BIOS程序启动从硬盘启动程序 5Authors:Guenter NissenHeiko Riemenschneid
5、erTraining document,no update service.This document may not be copied,partly or whole,or made be accessible to third parties without our permission and remains the property of B.Braun Medizintechnologie GmbH with all rights.27/10/2022治疗之前治疗之前冲洗水路 填充水箱,冲洗整个水路 6Authors:Guenter NissenHeiko Riemenschnei
6、derTraining document,no update service.This document may not be copied,partly or whole,or made be accessible to third parties without our permission and remains the property of B.Braun Medizintechnologie GmbH with all rights.27/10/2022自检自检所有测试步骤都由控制板控制完成监测板通过自己的传感器监测整个过程。监测板测试 D24V 和 B24V 电压继电器各 3 秒
7、。打开 24V 继电器,给控制板进行下一步测试提供电压。任一自检步骤如失败将自动循环监测该步骤。维修界面有自检程序代码,显示自检程序进度。7Authors:Guenter NissenHeiko RiemenschneiderTraining document,no update service.This document may not be copied,partly or whole,or made be accessible to third parties without our permission and remains the property of B.Braun Mediz
8、intechnologie GmbH with all rights.27/10/2022自检自检 维修界面维修界面 chapter 3 page 36-38自检代码 8Authors:Guenter NissenHeiko RiemenschneiderTraining document,no update service.This document may not be copied,partly or whole,or made be accessible to third parties without our permission and remains the property o
9、f B.Braun Medizintechnologie GmbH with all rights.27/10/2022自检自检 自检代码总览自检代码总览Code Test Code00 xxxNo tests or rinsing 16xxx Sound and LED test(from SW 7.51)17xxxLLC DFS Test 18(analog voltage test from SW 7.51 and sup.version 3)11xxxBlood leak detector12xxxDFS leakage test15xxx HDF online 完整性测试(only
10、for Dialog HDF online)20 xxx UF pump21xxx Conductivity22xxxTemperature TSD30 xxx SAD:level test31xxx SAD:counter test32xxx Pressure sensors blood side:equality test for blood side pressure sensors33xxx Pressure sensors blood side:blood side pressure test34xxx Substitution pump HDF bag(only for Dialo
11、g HDF bag)35xxx Flow detector HDF bag(only for Dialog HDF bag)36xxx Load cell HDF bag(only for Dialog HDF bag)37xxx Disinfection valve VD40 xxx Leakage test substitution line S online HDF online 9Authors:Guenter NissenHeiko RiemenschneiderTraining document,no update service.This document may not be
12、copied,partly or whole,or made be accessible to third parties without our permission and remains the property of B.Braun Medizintechnologie GmbH with all rights.27/10/2022自检状态自检状态 chapter 3 page 36 10Authors:Guenter NissenHeiko RiemenschneiderTraining document,no update service.This document may not
13、 be copied,partly or whole,or made be accessible to third parties without our permission and remains the property of B.Braun Medizintechnologie GmbH with all rights.27/10/2022自检自检 显示状态显示状态 11Authors:Guenter NissenHeiko RiemenschneiderTraining document,no update service.This document may not be copie
14、d,partly or whole,or made be accessible to third parties without our permission and remains the property of B.Braun Medizintechnologie GmbH with all rights.27/10/2022Sound and LED Test 报警声光测试报警声光测试可能测试到的配件:-LED/OSD Board defective-扬声器-触发器(主板或FPB板)-连线导电不良或接头松动-SMPS的维修跳线P101短路-SMPS 的继电器 VGB 或 VGDLLS 通过电流进行测试,两个OSD(Optical Status Display)板上的红色 LED灯 发光 同时 扬声器发出报警声(software version 7.5x)。Code LLC 1610 x-1699x/SUP 16001-16028 12Authors:Guenter NissenHeiko Riemenschneid
copyright@ 2008-2022 冰豆网网站版权所有
经营许可证编号:鄂ICP备2022015515号-1