IBM 内部员工操作手册簿 AIX HACMP 安装配置详细文档Word格式.docx

1、rsct.core.sec 2.4.2.1rsct.core.rmc 2.4.2.1AIX 5L v.5.2 plus ML 52.3.6pat.basic.hacmp 2.3.6.0pat.clients.hacmp 2.3.6.0rsct.core.sec 2.3.6.1rsct.core.rmc 2.3.6.1ii.此次安装的AIX 环境为AIX 5.3 ML6b）安装过程在安装HACMP的过程中，除HAview和HA Tivoli这两个安装包不装外，其他都正常安装c）安装HACMP补丁下载地址：-933.ibm./support/fixcentral/2.HACMP 5.4配置前的规划

2、工作：Cluster NameByh_clusterNode NameHA1HA2IP LabelHA1_bootHA1_svcHA1_stbHA2_bootHA2_svcHA2_stbIP Address10.10.10.1029.9.9.102192.168.0.110.10.10.1039.9.9.103192.168.0.2Persistent IPHA1_per: 9.181.1.100HA2_per: 9.181.1.101HeartBeatHb_HA1: /dev/hdisk1Hb_HA2: /dev/hdisk2Res. Grp. NameService IPVolume Gr

3、oupAppNameByh_rgSharevgNone3.HACMP5.4配置方法：a）配置两台机器的/etc/hosts文件：分别在/etc/hosts中加入：b）在HA1上，配置网路连接：i.配置HA1上boot IP-ent0上ii.配置HA1上stb IP-ent1上在HA2节点上也要将boot IP和stb IP也要提前配置好c）建立共享VG-sharevg和用于磁盘心跳的VG-convg这两个VG的* Activate volume group AUTOMATICALLY at system restart选项必须为No建好convg后，在Node1上执行/usr/sbin/rsc

4、t/bin/dhb_read -p hdisk1 -r命令在Node2上执行/usr/sbin/rsct/bin/dhb_read -p hdisk1 -t命令，确认可以正常通讯。d）通过smitty hacmp命令进行HACMP具体配置：Smitty hacmp选择Initialization and Standard Configuration选择Configure an HACMP Cluster and Nodes输入 Cluster Name在New Node选项中，按ESC+4选中HA1_boot和HA2_boot后回车执行成功后，进入下一步配置在Initialization an

5、d Standard Configuration菜单下，选择 Configure Resources to Make Highly Available选中 Configure Service IP Labels/Addresses选择Add a Service IP Label/AddressConfigure HACMP Resource Groups选择Add a Resource Group输入Resource Group Name，并在Participating Nodes （Default Node Priority）中执行ESC+4选中两个Node执行完该操作后，请退出至：选择Ex

6、tended Configuration选项：选择Extended Topology Configuration选择Configure HACMP Networks选择Add a Network to the HACMP Cluster选择磁盘心跳然后选择Configure HACMP Communication Interfaces/Devices选项：选择Add Communication Interfaces/Devices选择Add Pre-defined Communication Interfaces and Devices选择Communication Devices输入Devi

7、ce Name，Device Path和Node Name选择Extended Resource Configuration选择 HACMP Extended Resource Group Configuration选择 Change/Show Resources and Attributes for a Resource Group选择资源组的名称byhrg将service IP和共享VG添加到资源组中选择HACMP Extended Resources Configuration然后到Extended Configuration选择Extended Topology Configurati

8、on- Configure HACMP Persistent Node IP Label/Addresses选择Add a Persistent Node IP Label/Address选择Node名称将Network Name和Node IP Label/Address 按ESC+4完成HACMP基本配置完成进行HACMP Verification and SynchronizationHACMP同步完成启动HACMP启动HACMP完毕后，执行netstat i确定各个IP的状态测试HACMP在Node1上，网卡状态从变成Node2上网卡状态：Svc IP正常切换到Node2上。在Node2上 sharevg正常挂起资源组全部转移成功