cp5511是用于笔记本电脑通过mpiWord格式.docx

1、 You are using a CP5511 for setting up an online connection. If the connection is not set up as required, please run through the following checklist. Contents:1. What to watch out for when installing a CP5511 1.1 Installation of software products 1.2 Settings for the CP5511 1.3 Diagnostics options i

2、n STEP 7 after installing the CP5511 2. What are the particular points for each operating system?2.1 Windows 95 2.2 Windows 98 2.3 Windows 98 SE 2.4 Windows NT 2.5 Windows 2000/XP Professional 2.6 Memory conflict between CP 5511 and IBM Ethernet PCMCIA Adapter II 3. Error messages 3.1 CP5511 is ente

3、red in the Device Manager in SIMATIC NET with a yellow exclamation mark 3.2 Error: 0x0300 3.3 Error: 0029 interface error 3.4 Message: 33:16662 Online: connection cannot be set up to the target module 3.5 Error-free data transfer despite error message on the DP/PA link 3.6 CP5511 cannot be installed

4、 on the notebook with PCMCIA controller TI1225/TI1450 in Windows 98 3.7 Error message: Error 2 in the Registry when changing the IP address in Windows NT 3.9 Installation of CP5511 in Windows 98 with conflict 3.10 CP 5511 doesnt run with COM PROFIBUS in Windows 3.xx 3.11 Error in L2PC_DRV.DLL4. Dein

5、stallation of the CP5511 The computer must be at least a Pentium 90 MHz or equivalent.Hardware interface: PCMCIA （PC CARD） Type 2 or Type 3 according to PCMCIA standardPossible interrupts: IRQ5, IRQ10, IRQ11, IRQ12, IRQ15Memory window: max. 64KB, min. 16KB, position and size are adapted to the memor

6、y available in the PCPlug-and-play functionalityLicense:The authorization of STEP 7 is stored in the ax nf zz directory. Neither this directory nor the files stored in it are to be deleted. The license cannot be stored on a compressed drive. The license can also be installed later with AUTHORSW.EXE.

7、 Before deinstalling, transfer the license back to the floppy disk, otherwise it might be lost.The CP5511 is to be slotted and installed in the first slot of your notebook. Make sure in the case of a plug-and-play installation that there are enough free resources available. If not, then you must dis

8、able the sound card, the USB controller and the LPT port in the BIOS. In most notebooks there is a PCI configuration in the BIOS with IRQ Line 1-4. You should use IRQs 9 and 10 there. Using the PCMCIA card from IBM （IBM Ethernet credit card adapter II） can lead to a conflict in the memory assignment

9、. A function cannot be guaranteed for the CP5511 if this Ethernet card is installed together with the CP5511 for example in socket II. If you want to use the CP5511, then please remove the IBM cards.When installing software products （STEP 7, ProTool, WinCC, PDM, .） please make sure that the complete

10、 software is installed on the same drive. Close all Windows programs and the control panel before installation. In Windows NT you must be logged on as Administrator, otherwise the installation will be incomplete, because you wont be able to make essential entries in the Registry）.Via Start SIMATIC S

11、TEP 7 PG-PC Interface Settings you call the dialog for setting the parameters of the interface. Then click, for example, the interface parameter CP5511（PROFIBUS）. Press the Properties button and enable PG/PC is the only master on the bus if there is no other master connected to the bus. Then acknowl

12、edge with OK. Any warning you get about the access path being changed you confirm with . Note:You can check your connection by calling the PG-PC Interface dialog and pressing the Diagnostics button. Press the Test button to see whether your communication is set up and if you press the Read button, you can see whether your slave answers.We recommend that you read the information in our FAQ entitled No online connection with the CP5511, which is available in the Internet under Entry ID: 11492532.2. What are the particular points for each operating system 2.1. Windows 95 The follow