基于单片机的温度控制外文文献及中文翻译文档格式.docx

1、An Interdisciplinary Undergraduate Engineering Design ProjectJames S. McDonaldDepartment of Engineering ScienceTrinity UniversitySan Antonio, TX 78212Abstract：This paper describes an interdisciplinary design project which was done under the authors supervision by a group of four senior students in t

2、he Department of Engineering Science at Trinity University. The objective of the project was to develop a temperature control system for an air-filled chamber. The system was to allow entry of a desired chamber temperature in a prescribed range and to exhibit overshoot and steady-state temperature e

3、rror of less than 1 degree Kelvin in the actual chamber temperature step response. The details of the design developed by this group of students, based on a Motorola MC68HC05 family microcontroller, are described. The pedagogical value of the problem is also discussed through a description of some o

4、f the key steps in the design process. It is shown that the solution requires broad knowledge drawn from several engineering disciplines including electrical, mechanical, and control systems engineering.1 IntroductionThe design project which is the subject of this paper originated from a real-world

5、application. A prototype of a microscope slide dryer had been developed around an OmegaTM model CN-390 temperature controller, and the objective was to develop a custom temperature control system to replace the Omega system. The motivation was that a custom controller targeted specifically for the a

6、pplication should be able to achieve the same functionality at a much lower cost, as the Omega system is unnecessarily versatile and equipped to handle a wide variety of applications.The mechanical layout of the slide dryer prototype is shown in Figure 1. The main element of the dryer is a large, in

7、sulated, air-filled chamber in which microscope slides, each with a tissue sample encased in paraffin, can be set on caddies. In order that the paraffin maintain the proper consistency, the temperature in the slide chamber must be maintained at a desired （constant） temperature. A second chamber （the

8、 electronics enclosure） houses a resistive heater and the temperature controller, and a fan mounted on the end of the dryer blows air across the heater, carrying heat into the slide chamber. This design project was carried out during academic year 199697 by four students under the authors supervisio

9、n as a Senior Design project in the Department of Engineering Science at Trinity University. The purpose of this paper isto describe the problem and the students solution in some detail, and to discuss some of the pedagogical opportunities offered by an interdisciplinary design project of this type.

10、 The students own report was presented at the 1997 National Conference on Undergraduate Research 1. Section 2 gives a more detailed statement of the problem, including performance specifications, and Section 3 describes the students design. Section 4 makes up the bulk of the paper, and discusses in

11、some detail several aspects of the design process which offer unique pedagogical opportunities. Finally, Section 5 offers some conclusions.2 Problem StatementThe basic idea of the project is to replace the relevant parts of the functionality of an Omega CN-390 temperature controller using a custom-d

12、esigned system. The application dictates that temperature settings are usually kept constant for long periods of time, but its nonetheless important that step changes be tracked in a “reasonable” manner. Thus the main requirements boil down toallowing a chamber temperature set-point to be entered,di

13、splaying both set-point and actual temperatures, andtracking step changes in set-point temperature with acceptable rise time, steady-state error, and overshoot.Although not explicitly a part of the specifications in Table 1, it was clear that the customer desired digital displays of set-point and ac

14、tual temperatures, and that set-point temperature entry should be digital as well （as opposed to, say, through a potentiometer setting）.3 System DesignThe requirements for digital temperature displays and setpoint entry alone are enough to dictate that a microcontrollerbased design is likely the mos

15、t appropriate. Figure 2 shows a block diagram of the students design. The microcontroller, a MotorolaMC68HC705B16 （6805 for short）, is the heart of the system. It accepts inputs from a simple four-key keypad which allow specification of the set-point temperature, and it displays both set-point and m

16、easured chamber temperatures using two-digit seven-segment LED displays controlled by a display driver. All these inputs and outputs are accommodated by parallel ports on the 6805. Chamber temperature is sensed using a pre-calibrated thermistor and input via one of the 6805s analog-to-digital inputs. Finally, a pulse-width modulation （PWM） output on the 6805 is used to drive