1、Date日期Subject Of Revisi on 修改主题Prepared 编制Reviewed 审核Approved 批准No、序号Descriptionin spectio检验内容of nSta ndards for theIn specti on检验标准与依据Check the items核实内容WCESig nAIThirdPartClie ntRemarks1Material材料Plate钢板1、 ASME Code SectionVIII, Divisio n 1ASME规范第VIII卷第1 分册2、 ASME Code Section II-A ASME规范第II卷A篇3、
2、EN 10204 3、14、 Approved drawings图纸要求5、 MOM,Spec、1、 The dime nsion and mark shall suit with the releva nt requireme nts、 PMI shall be done as per the PMI procedure、 所采购得材料尺寸规格及标记必须符合相应标准得要求。按 照PMI程序对材料进行 PMI检验。2、 VT is required making sure there is no un acceptable surface defects-目视检查以确定没有无法接受得表面缺陷。
3、3 All material of all pressure retaining parts and its attachments shall be delivered with certificates, materials shall be delivered with mill certificates (Min、 3、1 certificates acc、 to EN10204)、 所有受压元件材料及其附件材料应提供合格证书,合格证书 至少符合 EN 10204 3、1。HWForge flange 锻件法2、 ASME Code Section II-AASME规范第II卷A篇Pi
4、pe接管1、 lhe dime nsion and mark shall suit with the releva nt requireme nts、 PMI shall be done as per the PMI procedure、 所采购得材料尺寸规格及标记必须符合相应标准得要求。Description in spectio 检验内容Gaskets&Faste ner(boltsand n uts) 紧固件1、 The dime nsion and mark shall suit with the releva ntrequireme nts、 PMI shall be done as
5、 per the PMI procedure、所采购得材料尺寸规格及标记必须符合相应标准得要求。2、 VT is required making sure there is no un acceptable surface defects目视检查以确定没有无法接受得表面缺陷。3 All material of all pressure retaining parts and its attachments shall be delivered with certificates; materials shall be delivered with mill certificates (Min、
6、 3、1 certificates acc、to EN10204)、所有受压元件材料及其附件材料应提供合格证书,合格证书至 少符合 EN 10204 3、1。4、 Exter nal carb on steel bolts and nuts and washer shall be hot dip galva ni zed、 And all CS bolts above the size of M27 shall be galvanized by using Low Dip (450470-Deg、 C) or a chemical process.外部用碳钢螺柱/螺母应进行热浸渡。公称直径大于
7、 M27得碳钢螺柱需要用低温浸锌(450470-度)或者化学过 程处理。Weldi ng material 焊接材 料VIII, Divisio nASME规范第VIII卷第1分册2、 ASME Code SectionII-CASME规范第II卷C篇3、 EN 10204 2、24、 Approved WPS5、 MOM1、 Package, marks shall be plete焊接材料得包装、标识必须完好。2、 The weld ing material shall be in con trol duri ng the dry, use, gra nt and reclaim、焊接材料
8、得烘烤、领用、发放与回收必须处于受控状态。3、 VT is required making sure there is no un acceptable surface defects-目视检查以确定没有无法接受得表面缺陷No-pres s、 Parts非受压件II-A1、 The mark, dimension of the material must suit with the certificates、材料得标识、尺寸必须与质量证明书一致。R5701Descripti on of in specti on 检验内容2Welder焊工1、ASME Code, section IXASME规范第IX1、 The welders must have the welder certificates by ASME codeand get the releva nt WPQ certificates, so that they can do the weldi ng f
copyright@ 2008-2022 冰豆网网站版权所有
经营许可证编号:鄂ICP备2022015515号-1