1、 toe ring) 钢圈,也称 toe ring Bead Ring Register The landing and tapered seat that the bead ring fits into 钢圈配合:侧板上,和 钢圈配合的平面及锥面 Bottom Container Plate The plate that the bottom sidewall plate is bolted to 模壳底座 Bottom Container Plate Lifting Lug A lug attached to the Bottom Container Plate with Horizont
2、al holes used for lifting. 模壳底座吊耳: 装配在底座上、有水平的孔,用来吊装的吊耳 Bottom Container Plate Dowel Pin Lug A lug attached to the Bottom Container Plate that supports the Dowel Pin Bushing. 装配在底座上,用来支承定位销套的突缘 Bottom Container Plate Hold Down A lug that is used to fix the Bottom Plate in the Press. 用来将底座装配在硫化机上的突缘
3、Breaker Hook A hook fixed to the bottom of the tread segment that catches the bottom container plate only when the segment will not release from the tire during de-molding. 分离钩:固定在花纹块底部的钩子,轮胎硫化完后若花纹块不能跟轮胎分离,就用此钩抓住模壳底座帮助花纹块和轮胎进行分离。. Breaker Hook Guide Piece A block bolted to the breaker hook that ali
4、gns the tread segment with a slot in the bottom container plate. 分离钩导块:用螺栓固定在Breaker Hook上,定位花纹块和模壳底座上槽的定位块。Bronze Wear Plates Any sacrificial metal plate placed under, over or behind a component to keep the components from wearing on each other (greasing) 青铜耐磨板(油润滑的) Casting An un-machined cast met
5、al tread ring or Segment 铸件:未加工的金属花纹圈或花纹块铸件。Centering Ring The ring mounted on the bottom press platen to locate the mold/ container concentrically to the press; Press register 定中环,也称“Press register” Clamp Rings The bladder clamping assembly 胶囊夹盘 Cone Ring The outer ring that transforms the axial mo
6、vement of the press in a radial one of the segments; Actuator ring, Squeeze ring (GT) 导环,也称Actuator ring, Squeeze ring Conicity Difference between tread radius over the width 锥度 Container The mechanical parts that allow a segmented mold to operate; mechanism (GT) 模壳,也叫 mechanism Container Cavity The
7、 space inside of the container that the mold fits into 模壳腔:模壳部放置模具的空间。DD-Diameter Nominal diameter of a bead ring (EU) Also: Heel diameter (GT) 钢圈的公称直径, 也叫Heel diameter Decoupler Rib A narrow rib that runs circumferentially around the mold and is located near the shoulder area 在胎肩部位、窄的的圆周向的花筋 DEVA M
8、etal Graphite impregnated bronze metal used for wear plates in segmented molds (un-greased) DEVA类耐磨板:石墨青铜金属,用来制作活络模具的耐磨板(自润滑)。Dowel Pins The pins that keep the mold halves and parts aligned (containers or HKK molds) 定位销:用来对模具的半模或零件定位的销(模壳或HKK模具)。Dowel Pin Bushing A replaceable sleeve used to registe
9、r the Dowel Pin locations. 定位销套:对定位销进行定位的可更换的衬套。DS 2-Diameter The junction diameter between the sidewall plate and the tread segments or tread ring and mould back cavity (EU); S Diameter(GT) 口径:侧板与花纹块、花纹圈与mould back 的配合直径. 也叫S Diameter End Gap The distance between cold mold segments (20C) that allow
10、s for heat expansion 竖缝间隙: 20C时花纹块竖缝允许热膨胀的间隙 Exterior Mold Identification Plate A removable plate fastened to the outside of the cone ring listing information pertaining to the mold parts (tread segments, side-plates) assembled in the container. 模壳铭牌 Filler rings Full sidewall inserts for molds that
11、 fills from the off shoulder area to the I.D. 嵌入式侧板:从肩部到径,全部嵌入模具的侧板 Front of mould The reference point at which all dimensional locations are referred 模具正前方 Heel Diameter See: DD-Diameter 见 DD-Diameter Guide Piece A block fixed to the Top Container Plate that registers to a slot in the Cone Ring to
12、keep the Top plate from turning during operation. 导向块:固定在上盖上,和导环上的槽定位,防止操作过程中上盖转动 Insert Metal plates pushed or screwed in the side wall plate for exchangeable information活字块(牌) Insulation Jacket Insulation placed around a container or 2 piece mold (GT) to retain heat 保温套 Integral type mechanism A m
13、old (tread area) and mechanism that are one unit 整体式模壳: 花纹部分和模壳是一体的 Ledge Height Bead ledge width on a bead ring 钢圈上凸出部位的宽度 Lettering The inside lettering of the sidewall; Sidewall engraving (GT) 侧板字体图. 也叫Sidewall engraving Maxi Vent (GT) Vent Sleeve A removable insert for vent holes (Dia.:1,33 mm)
14、to be trimmed. 大气孔套(直径.:1,33 mm) Mechanism (GT) See: container or semi-container 见container 或semi-container Micro Vent A removable insert with vent slots ( 0.1 mm) 微型气孔套:(Mini Vent (MV) A removable insert for vent holes (Dia.: 0,6 mm) 迷你气孔套(直径.:0.6 mm) Mold Back The part of a two piece mold machined to hold the tread ring and filler rings 除花纹圈和嵌入侧板外的两半模外壳 Mold Cavity The inside of the mold that the tyre is shaped in 模具腔:形成轮胎外型
copyright@ 2008-2022 冰豆网网站版权所有
经营许可证编号:鄂ICP备2022015515号-1