1、3.1.1 流量计算公式113.1.2 水头损失计算公式113.2 槽底纵坡i、槽身净宽B和净深H的设计123.2.1拟定i 、B和H的值123.2.2 总水头损失Z校核与i、B和H值的确定133.3 进出口高程确定133.3.1 高程计算公式133.3.2 高程计算结果143.4 进出口渐变段长度确定143.5 水力计算结果示意图144 槽身设计154.1 尺寸设计154.1.1扶栏154.1.2人行道板154.1.3拉杆154.1.4侧墙154.1.5底板164.1.6 渡槽横剖面示意图164.2 槽身各部分荷载及自重164.3 人行道板配筋设计174.4 拉杆、侧墙、底板横向配筋设计17
2、4.4.1内力计算174.4.2配筋设计204.5 拉杆、侧墙、底板纵向配筋设计214.5.1计算简图214.5.2内力计算214.5.3配筋设计224.6 槽身抗裂验算224.6.1 横向抗裂验算224.6.2 纵向抗裂验算254.7 槽身吊装验算254.7.1吊装施工布置及其示意图264.7.2吊装内力计算264.7.3吊装验算265 重力墩计算275.1 重力墩尺寸确定275.1.1 渡槽高度及柱底高程计算285.1.2 重力墩局部尺寸确定285.2 重力墩设计305.2.1 重力墩墩身设计306 基础326.1基础尺寸确定326.1.1 基础形式选择326.1.2 尺寸初步确定326.
3、1.3 基础尺寸验定337 渡槽及其地基稳定性验算347.1 渡槽整体性验算347.1.1 抗滑稳定性验算347.1.2 抗倾覆稳定性验算347.2 渡槽抗滑稳定性验算357.2.1 空槽工况下抗滑稳定性验算357.2.2 满槽工况下抗滑稳定性验算367.3 渡槽抗倾覆稳定性验算367.3.1 空槽工况下抗倾覆稳定性验算367.3.2 满槽工况下抗倾覆稳定性验算377.4 基底压应力验算377.4.1 横槽向基底压应力验算377.4.2 顺槽向基底压应力验算378.Ansys有限元计算分析388.1Ansys有限元基本简介:388.2渡槽平面模型的建立388.2.1Ansys平面渡槽模型398
4、.8.2结构力学求解器渡槽平面计算398.3渡槽三维模型的建立398.3.1创建渡槽三维模型408.3.2网格划分408.3.3边界条件及施加荷载408.3.4求解及后处理408-4结果及分析408.4.1Ansy平面结构分析408.4.2结构力学求解器结构分析408.4.3Ansys三维结构分析418.5计算结果对比分析418.5.1平面计算结果分析418.5.2三维有限元结果分析429 细部结构429.1 伸缩缝及止水429.2 支座439.3 两岸连接44致 谢45参考文献46附录:计算说明书481 水力计算481.1 水力计算公式481.2 加大流量下水力计算491.3 设计流量下的水
5、力计算491.4 水头损失计算501.5 高程计算511.6 进出口渐变段长度计算511.7 水力计算结果522 槽身各部分荷载计算522.1 扶栏自重532.2人群荷载532.3人行道板自重542.4 拉杆自重542.5 侧墙自重542.6 底板自重552.7 设计水流下水自重552.8 加大水流下水自重562.9 槽身各细部自重结果563人行道板配筋计算563.1 计算简图573.2 荷载及内力计算573.3 配筋计算584 槽身计算584.1 槽身横向计算584.1.1内力计算584.1.2配筋计算674.2 槽身纵向计算734.2.1 槽身纵向计算简图734.2.2 槽身纵向荷载及内力
6、计算744.2.3 槽身纵向配筋计算754.3 槽身抗裂验算764.3.1 槽身横向抗裂验算764.3.2 槽身纵向抗裂验算814.4 槽身吊装验算834.4.1吊装布置及其示意图834.4.2吊装内力计算834.4.3槽身吊装验算845 槽墩计算855.1 槽墩尺寸确定855.1.1 渡槽高度计算855.1.2 重力墩局部尺寸确定865.2 重力墩的设计说明875.2.1 水平方向荷载计算915.2.2 竖直方向荷载计算945.2.3 墩帽局部承受压力计算956 基础966.1 基础尺寸确定976.1.1基础形式选择976.1.2 尺寸初步确定976.1.3 基础尺寸验定987 渡槽稳定性验
7、算1007.1 渡槽槽身的整体性验算1007.1.1 抗滑稳定性验算1007.1.2 抗倾覆稳定性验算1017.2 渡槽整体抗滑稳定性验算1027.2.1 空槽工况下抗滑稳定性验算1027.2.2 满槽工况下抗滑稳定性验算1037.3 渡槽抗倾覆稳定性验算1037.3.1 空槽工况下抗倾覆稳定性验算1047.3.2 满槽工况下抗倾覆稳定性验算1047.4 基底压应力验算1047.4.1 横槽向基底压应力验算1048. Ansys有限元计算分析1058.1Ansys有限元基本简介1058.2渡槽平面模型的建立1058.2.1Ansys平面渡槽模型1058.8.2结构力学求解器渡槽平面计算1088
8、.3渡槽三维模型的建立1098.3.1创建渡槽三维模型1098.3.2网格划分1108.3.3边界条件及施加荷载1108.3.4求解及后处理1118-4结果及分析1128.4.1Ansy平面结构分析1128.4.2结构力学求解器结构分析1138.4.3Ansys三维结构分析1148.5计算结果对比分析1158.5.1平面计算结果分析1158.5.2三维有限元结果分析116 第4页,共122页林家河渡槽设计学 生:指导老师:三峡大学水利与环境学院摘要:本文采用传统设计方法对林家河渡槽进行了整体设计。首先,通过对林家河周边地形和地质条件分析,根据渡槽结构型式特点,确定本渡槽型式为简支梁式渡槽,槽身
9、采用矩形横截面,支撑结构采用实体重力墩形式,基础采用整体板式基础;然后参照水工设计规范和工程中渡槽设计经验值确定各部分尺寸并进行校核,再进行各部分的内力计算、配筋计算、抗裂验算及细部处理,最后采用Ansys有限元软件进行平面计算和三维模型计算与结构力学求解器计算的结果进行比较,利用其结果对渡槽进行强度校核,检验渡槽各部分以及整体是否满足强度和稳定性要求,并对设计值进行修正以达到最优效果。通过本次毕业设计,将大学本科所学的专业知识与工程实际相结合,提高了水利水电专业素养,达到了毕业设计的预期效果。Abstract: In this paper,Lin Jiahe aqueduct has bee
10、n overall designed using the traditional methods combined with the engineering concept. At first, according to the analysis of the terrain and geology condition and the comparision of the characteristics of each kinds of aqueducts, the structure form of simply supported beam aqueduct is decided, so
11、the cross-section of the body of the aqueduct is rectangular, the supporting structure is the gravity abutment , and the foundation is a integral plate type foundation. The second, in order to determine the size of each component of aqueduct, the experience datas from practical engineerings are stud
12、ied and used in the paper. Then, the internal force of each component is calculated, the reinforcement calculation and checking calculation for crack are finished, and the details sturcture is dealt with. At last,Ansys finite element software planar and three-dimensional model calculations and struc
13、tural mechanics solver calculation results were compared , using its strength check results Aqueduct. Both the parts and the whole of the aqueduct is tested to know whether the aqueduct is satisfied with the requirements for the strength and the stability ,and correct the design datas to optimize the result of the design.Through this graduation design,professional knowledge and Engineering Bachelors degree studies the actual combination, improve the professional quality of the water conservancy and hydroelectric power, to achieve the desired effect of graduation design.关键词:水利水电 渡槽 水力计算 配筋计算
copyright@ 2008-2022 冰豆网网站版权所有
经营许可证编号:鄂ICP备2022015515号-1