A5680T下挂5620E开局指导.docx

1、A5680T下挂5620E开局指导1. 组网图2.配置实例：本次以5680T/5606T 作为olt，下挂5620E/5626E,由于5626E只有FE口，而5620E既有FE口，又有窄带，故以5680T下挂 5620E为例，数据规划如下：5620E管理vlan 37 ， 管理IP 为 10.5.2.7 。宽带业务采用Q-IN-Q ，外层VLAN 174（按局方要求在5680T上打外层VLAN标签） ，8个FE 端口的 内层 VLAN 为 501 到 508 。语音业务VLAN 为 2800 ，mg_ip（5620E作为AG的地址）为 10.208.180.2 端口号为 2944（UDP端口号

2、） ，mgc_ip（兰州软交换的地址） 为 61.134.70.1 端口号为 2944 ！ 注意：VOIP业务时，张掖地区软交换地址(BAC)通常为61.134.70.1， 但是具体开局时请以申请数据为准， 配置5680T数据： User name:root User password: Huawei Integrated Access Software. Copyright(C) Huawei Technologies Co., Ltd. 2002-2008. All rights reserved. zhongxinjun_MA5680Tenable zhongxinjun_MA5680T

3、#config zhongxinjun_MA5680T(config)#switch language-mode 当前语言模式已切换到本地语种 zhongxinjun_MA5680T(config)#interface epon 0/1 zhongxinjun_MA5680T(config-if-epon-0/1)#port 0 ont-auto-find enable /打开自动发现功能 Command: port 0 ont-auto-find enable zhongxinjun_MA5680T(config-if-epon-0/1)#port 1 tag-based-vlanzhong

4、xinjun_MA5680T(config-if-epon-0/1)# 端口配置命令执行成功 当ONU连接正常时出现自动发现ONU的告警:告警名称 : ONU自动发现参数信息 : 机框号: 0, 槽位号: 1, 端口号: 0, MAC: 0018-8282-891B, 密码: -告警描述 : ONU自动发现告警原因 : ONU自动发现修复建议 : 如果ONU合法则确认,否则删除此ONUzhongxinjun_MA5680T(config-if-epon-0/1)#ont confirm 0 ontid /确认ONU，相应模板已经配置， ontid :0 password-auth|mac-au

5、th :mac-auth mac :0018-0000-0001 profile-id|profile-name :profile-id profile-id :30 |multicast-mode|multicast-fast-leave|description|fec|dba-profile|encrypt|cir :dba-profile profile-id :10 |multicast-mode|multicast-fast-leave|description|fec|encrypt|cir : Command: ont confirm 0 ontid 0 mac-auth 0018

6、-0000-0001 profile-id 30 dba-profile 10 zhongxinjun_MA5680T(config-if-epon-0/1)#quit zhongxinjun_MA5680T(config)#vlan 37 smart /网管VLAN zhongxinjun_MA5680T(config)#vlan 174 smart /宽带业务VLAN zhongxinjun_MA5680T(config)#vlan 2800 smart /voip 业务 zhongxinjun_MA5680T(config)#vlan attrib 174 q-in-q / 设置VLAN

7、174属性为q-in-q zhongxinjun_MA5680T(config)#bpdu tunnel vlan 174 enable zhongxinjun_MA5680T(config)# zhongxinjun_MA5680T(config)#port vlan 37 0/20 0 zhongxinjun_MA5680T(config)#port vlan 174 0/20 0 zhongxinjun_MA5680T(config)#port vlan 2800 0/20 0 zhongxinjun_MA5680T(config)# zhongxinjun_MA5680T(config

8、)# zhongxinjun_MA5680T(config)#service-port vlan 37 adsl|shdsl|vdsl|atm|eth|gpon|epon :epon frameid/slotid/portid :0/1/0 ont :ont ontid :0 |multi-service :multi-service user-vlan :user-vlan user-vlanid|untagged :37 Command: service-port vlan 37 epon 0/1/0 ont 0 multi-service user-vlan 37 zhongxinjun

9、_MA5680T(config)# zhongxinjun_MA5680T(config)# zhongxinjun_MA5680T(config)#service-port index|vlan|desc :vlan vlanid|aoe :174 adsl|shdsl|vdsl|atm|eth|gpon|epon :epon frameid/slotid/portid :0/1/0 ont :ont ontid :0 |multi-service :multi-service user-vlan :user-vlan user-vlanid|untagged :501 Command: s

10、ervice-port vlan 174 epon 0/1/0 ont 0 multi-service user-vlan 501 zhongxinjun_MA5680T(config)#service-port vlan 174 epon 0/1/0 ont 0 multi-service user-vlan 502 zhongxinjun_MA5680T(config)#service-port vlan 174 epon 0/1/0 ont 0 multi-service user-vlan 503 zhongxinjun_MA5680T(config)#service-port vla

11、n 174 epon 0/1/0 ont 0 multi-service user-vlan 504 zhongxinjun_MA5680T(config)#service-port vlan 174 epon 0/1/0 ont 0 multi-service user-vlan 505 zhongxinjun_MA5680T(config)#service-port vlan 174 epon 0/1/0 ont 0 multi-service user-vlan 506 zhongxinjun_MA5680T(config)#service-port vlan 174 epon 0/1/

12、0 ont 0 multi-service user-vlan 507 zhongxinjun_MA5680T(config)#service-port vlan 174 epon 0/1/0 ont 0 multi-service user-vlan 508 zhongxinjun_MA5680T(config)#service-port vlan 2800 epon 0/1/0 ont 0 multi-service user-vlan 2800 zhongxinjun_MA5680T(config)#display service-port all |sort-by : Command:

13、 display service-port all - INDEX VLAN VLAN PORT F /S /P VPI VCI FLOW FLOW RX TX STATE ID ATTR TYPE TYPE PARA - 0 37 common epon 0 /1 /0 0 - vlan 37 - - up 1 174 QinQ epon 0 /1 /0 0 - vlan 501 - - up 2 174 QinQ epon 0 /1 /0 0 - vlan 502 - - up 3 174 QinQ epon 0 /1 /0 0 - vlan 503 - - up 4 174 QinQ e

14、pon 0 /1 /0 0 - vlan 504 - - up 5 174 QinQ epon 0 /1 /0 0 - vlan 505 - - up 6 174 QinQ epon 0 /1 /0 0 - vlan 506 - - up 7 174 QinQ epon 0 /1 /0 0 - vlan 507 - - up 8 174 QinQ epon 0 /1 /0 0 - vlan 508 - - up 9 2800 common epon 0 /1 /0 0 - vlan 2800 - - up - Total : 10 (Up/Down : 10/0) Note : F-Frame

15、, S-Slot, P-Port, VPI indicates GEM PortID for GPON or ONT ID for EPON, pri-tag indicates priority-tagged zhongxinjun_MA5680T(config)# zhongxinjun_MA5680T(config)# zhongxinjun_MA5680T(config)# zhongxinjun_MA5680T(config)# /在olt上远程配置5620E 网管数据 zhongxinjun_MA5680T(config)#interface epon 0/1 zhongxinju

16、n_MA5680T(config-if-epon-0/1)#ont ipconfig portid :0 ontid :0 ip-address :ip-address ip-address :10.5.2.7 mask :mask mask :255.255.255.0 gateway :gateway gateway :10.5.2.1 manage-vlan :manage-vlan managevlan :37 Command: ont ipconfig 0 0 ip-address 10.5.2.7 mask 255.255.255.0 gateway 10.5.2.1 manage

17、-vlan 37 zhongxinjun_MA5680T(config-if-epon-0/1)# The ONT IP is configured successfully zhongxinjun_MA5680T(config-if-epon-0/1)#quit zhongxinjun_MA5680T(config)#ping 10.5.2.7 PING 10.5.2.7: 56 data bytes, press CTRL_C to break Reply from 10.5.2.7: bytes=56 Sequence=0 ttl=63 time = 13 ms zhongxinjun_

18、MA5680T(config)#telnet 10.5.2.7 /登陆到5620E上配置业务 |service-port : Command: telnet 10.5.2.7 Press CTRL_ to quit telnet mode Trying 10.5.2.7 . Connected to 10.5.2.7 . 配置5620E数据： (5620E密码为mduadmin) User name:root User password: Huawei Integrated Access Software. Copyright(C) Huawei Technologies Co., Ltd.

19、1998-2008. All rights reserved. - User last login information: - Access Type: Telnet IP-Address : 61.178.177.99 Time : 2000-01-12 03:53:33 - MA5620Eenable MA5620E#time 2008-10-13 / 修改系统时间 |time :13:00:00 Command: time 2008-10-13 13:00:00 MA5620E#config MA5620E(config)#sysname ceshi_5620e /修改系统名 cesh

20、i_5620e(config)#vlan 501 to 508 /宽带业务内层VLAN Are you sure to add VLANs? (y/n)n:y ceshi_5620e(config)#vlan 2800 /voip vlan Command: vlan 2800 ceshi_5620e(config)#port vlan 2800 0/0 1 ceshi_5620e(config)#port vlan 501 to 508 0/0 1 Are you sure to add standard port(s)? (y/n)n:y ceshi_5620e(config)#undo

21、service-port all /删除原来的service-port It will take several minutes, and console may timeout, please use command idle-timeout to set time limit Are you sure to release service virtual port(s)? (y/n)n:y 显示流量表模板：ceshi_5620e(config)#display traffic table ip from-index 0 |to-index : 命令： display traffic tab

22、le ip from-index 0 - 流量 CIR(kbps) CBS(bytes) PIR(kbps) PBS(bytes) Color 优先级 拷贝策略 调度策略 索引 Mode - 0 512 18384 1024 36768 Blind 6 - tag-pri 1 1024 34768 2048 69536 Blind 0 - tag-pri 2 2048 67536 4096 135072 Blind 0 - tag-pri 3 4096 133072 8192 266144 Blind 4 - tag-pri 4 8192 264144 16384 528288 Blind 4

23、 - tag-pri 5 16384 526288 32768 1024000 Blind 4 - tag-pri 6 off off off off - 0 - tag-pri - 总数 : 7缺省情况下，系统启动后有7个流量表项，索引号为0-6。这7个缺省的流量表项可以被删除。在下面增加业务流时根据实际情况引用ceshi_5620e(config)#service-port desc|index|vlan :vlan transparent|vlanid :501 eth :eth frameid/slotid/portid :0/1/1 other-all|user-encap|user

24、-vlan :user-vlan untagged|user-vlanid :untagged rx-cttr :rx-cttr 6 tx-cttr :tx-cttr 6 Command: service-port vlan 501 eth 0/1/1 user-vlan untagged rx-cttr 6 tx-cttr 6 ceshi_5620e(config)#service-port vlan 502 eth 0/1/2 user-vlan untagged rx-cttr 6 tx-cttr 6 ceshi_5620e(config)#service-port vlan 503 e

25、th 0/1/3 user-vlan untagged rx-cttr 6 tx-cttr 6 ceshi_5620e(config)#service-port vlan 504 eth 0/1/4 user-vlan untagged rx-cttr 6 tx-cttr 6 ceshi_5620e(config)#service-port vlan 505 eth 0/1/5 user-vlan untagged rx-cttr 6 tx-cttr 6 ceshi_5620e(config)#service-port vlan 506 eth 0/1/6 user-vlan untagged

26、 rx-cttr 6 tx-cttr 6 ceshi_5620e(config)#service-port vlan 507 eth 0/1/7 user-vlan untagged rx-cttr 6 tx-cttr 6 ceshi_5620e(config)#service-port vlan 508 eth 0/1/8 user-vlan untagged rx-cttr 6 tx-cttr 6 ceshi_5620e(config)# /在5620E上配置语音业务：(voip) ceshi_5620e(config)# ceshi_5620e(config)# ceshi_5620e(config)#interface vlanif 2800 /配AG(5620E) 语音业务 ip 地址 ceshi_5620e(config-if-vlanif2800)#ip address ip_addr : 10.208.180.2 integer|ip_mask :24 Command: ip address 10.208.180.2 24 ceshi_5620e(config-if-vlanif2800)#quit ces