ncr英文码表.docx

1、ncr英文码表 CURRENCY DISPENSER M-STATUS00 No error01 Dispense requested from a cassette which is not installed or no cassettes installed during self-test.02 Too many bills being rejected, for example, undersize, oversize, multiple or extra bills.03 Pick failure.04 Pick failure plus low (out of bills).05

2、 Sensor failure or currency jam in main transport.06 Reserved07 Purge bin not present.08 Purge bin overfill sensor blocked.09 Communications failure between Command and Execution firmware. Current replenishment information may not have been determined.10 Operation not attempted because the device or

3、 a cassette type is FATAL form a previous operation. (A rest of SOH to HEALTHY must be performed to clear this condition).11 Operation not attempted due to one of the following: Bills are still stacked in the transport from a previous operation. Bills may not have been cleared from the transport due

4、 to an unrecovered error during a previous operation. The dispenser has been powered up and no CLEAR/CLEAR-DIAG has been issued. A CLEAR must be performed to clear this condition.12 Presenter clamping mechanism failed or jammed.13 Exit shutter jammed open.14 Exit shutter jammed closed.15 Reserved16

5、Main transport timing disk did not operate correctly or the main ac motor failed.17 Reserved.18 Currency jam in presenter transport or transport sensor failure.19 Exit sensor blocked on next operation after a good present. (Bills may not have been removed from exit slot).20-27 Reserved28 An area or

6、NVRAM cannot be accessed (SOH cannot be updated).29 Presenter transport timing disk did not operate correctly or motor failed.30 One of the presenter transport sensors failed clear or blocked.31 Reserved32 Heartbeat on execution processor failed (80652).33 Communications failure on the 12C bus of th

7、e execution processor (80652).34 A present bills operation has been attempted without any bills being stacked or a retract operation has been attempted with no bills presented.35 Operation incomplete due to ac and 24V dc power disconnection through interlock.36 Pick valve test not attempted because

8、cassettes were installed.37 TI service switched ON.38 TI service switched OFF.39 LVDT or associated circuitry malfunctioning.40 Bill parameters not configured.41 An attempt to pick from a cassette which has been disabled for In Service Replenishment.146 SDC link failure.M-DATAByte 0 Firmware level c

9、ommands:00 Reset01 Stack02 Present03 Move clamp to present04 Clear main transport05 Check if bills taken06 Purge07 Set bill widths08 Set bill singularities09 Set bill presentation order0A Read dispense counts0B Clear dispense counts0C Read configured parameters0D Read container status0E Read virtual

10、 cassette type0F Rotate to home position10 Close shutter command11 Main motor test12 Pick valve test13 Learn bill parameters14 Exit shutter test15 Presenter bill motor test16 Presenter clamp test17 Sensor test1B Disable Hamming Codes1C Pre-presentDISPENSER M-DATA (Byte 0=01,04,13)Byte 1 Main Dispens

11、er Status:Bit 7=1 Virtual cassette type/position 3 is low on billsBit 6=1 Virtual cassette type/position 4 is low on billsBit 5=0 AlwaysBit 4=1 Pick fail occurredBit 3=1 Fatal malfunction INOP flag setBit 2=1 Self test commandBit1=1 Virtual cassette type/position 1 is low on billsBit0=1 Virtual cass

12、ette type/position 2 is low on billsByte 2 Auxiliary Status Virtual Cassette Type 1:02 Purge bin not installed03 Pick failure04 Invalid pick interrupt09 Bill seen at pre-LVDT sensor when not expected0C Purge bin overfill or SOH active initially on stack or at end of clear10 Exit shutter not closed o

13、r closed sensor failed indicating not closed, or open sensor failed indicating open11 Pick sensor blocked initially or SOH active initially or at end of clear14 Pre-LVDT sensor blocked or SOH active initially or at end of clear21 Pre-LVDT failed clear during operation22 Pre-LVDT sensor failed blocke

14、d or bill jam during operation27 Presenter clamp not in home position initially or clamp home sensor failed blocked40 Virtual cassette type not installed41 TSEN 1 blocked or SOH active initially on stack or at end of clear (purge path)42 TSEN 2 blocked or SOH active initially on stack or at end of c

15、lear (clamp position)43 TSEN 3 blocked or SOH active initially on stack or at end of clear44 TSEN 4 blocked or SOH active initially on stack or at end of clear45 TSEN 5 blocked or SOH active initially on stack or at end of clear (exit sensor for 567X R/A)46 TSEN 6 blocked or SOH active initially on

16、stack or at end of clear47 TSEN 7 blocked or SOH active initially on stack or at end of clear (exit sensor for 567X F/A)48 TSEN 8 blocked or SOH active initially on stack or at end of clear (exit sensor for 568X TTW)49 12C failure initially4A 12C failure during operation4B Main transport timing disk

17、 too slow4C Reserved4D Main transport timing disk failed4E Pick sensor failed clear initially4F Pick sensor failed blocked or jam during operation50 Pre-LVDT sensor failed clear initially51 TSEN 1 failed clear initially on stack or at end of clear52 TSEN 2 failed clear initially on stack or at end o

18、f clear53 TSEN 3 failed clear initially on stack or at end of clear54 TSEN 4 failed clear initially on stack or at end of clear55 TSEN 5 failed clear initially on stack or at end of clear56 TSEN 6 failed clear initially on stack or at end of clear57 TSEN 7 failed clear initially on stack or at end o

19、f clear58 TSEN 8 failed clear initially in stack or at end of clear59 Purge bin overfill failed clear initially5A Gulp feed detected5B Interlock open initially5C Interlock open during operation60 Reference null reading too low LVDT#1 (right-hand)61 Reference null reading too low LVDT#2 (left-hand)62

20、 Reference null reading too high LVDT#1 (right-hand)63 Reference null reading too high LVDT#2 (left-hand)64 LVDT fault-too few timing wheel interrupts received on execution processor65 LVDT fault-execution processor did not receive a response to an LVDT request within the required time70 Cassette al

21、ready FATAL because of too many pick fails, rejects cassette empty or could not leam from cassette71 Too many interrupts at pick sensor or pre-LVDT sensor72 Bill parameters not configured73 Total thickness of bills picked on a bill leam has reached the limit that can safely be purgedByte 3 Auxiliary

22、 Status Virtual Cassette Type 2. (Same as for Byte 2)Byte 4 Auxiliary Status Virtual Cassette Type 3. (Same as for Byte 2)Byte 5 Auxiliary Status Virtual Cassette Type 4. (Same as for Byte 2)Byte 6 Divert Reason, Virtual Cassette Type 1.Bit 7=1 Inaccurate bill count or unable to leam bill parameter

23、during leam Bill Parameters commandBit 6=1 Thermistor indicates coldBit 5=1 Cassette not installedBit 4=1 At least one extra bill detectedBit 3=1 At least one long bill detectedBit 2=1 At least one short bill detectedBit 1=1 At least one multiple bill detectedBit 0=1 At least one over length bill de

24、tectedByte 7 Divert Reason, Virtual Cassette Type 2. (Bit information same as Byte 6)Byte 8 Divert Reason, Virtual Cassette Type 3. (Bit information same as Byte 6)Byte 9 Divert Reason, Virtual cassette Type 4. (Bit information same as Byte 6)PRESENTER M-DATA (Byte 0=02,03,06,0F,1C)Byte 1 Presenter

25、Status:00 Operation successful01 Shutter jammed closed during operation or open sensor failed indicating not open02 Shutter jammed open during operation or closed sensor failed indicating not closed04 Clamp not in correct position initially06 Clamp jammed moving home or home sensor failed showing no

26、t home07 Clamp jammed moving to present or present sensor failed showing not present0C Overfill sensor blocked initially11 Overfill sensor failed clear13 Overfill sensor blocked at end of purge operation14 TSEN 1 blocked or SOH line active initially on present or at end of purge15 TSEN 2 blocked or

27、SOH line active initially on present or at end of purge16 TSEN 3 blocked or SOH line active initially on present or at end of purge17 TSEN 4 blocked or SOH line active initially on present or at end of purge18 TSEN 5 blocked or SOH line active initially on present or at end or purge19 TSEN 6 blocked

28、 or SOH line active initially on present or at end of purge1A TSEN 7 blocked or SOH line active initially on present or at end of purge1B TSEN 8 blocked or SOH line active initially on present or at end of purge1C TSEN 1 failed clear initially on present on at end of purge1D TSEN 2failed clear initi

29、ally on present or at end of purge1E TSEN 3 failed clear initially on present or at end of purge1F TSEN 4 failed clear initially on present or at end of purge20 TSEN 5 failed clear initially on present or at end of purge21 TSEN 6 failed clear initially on present or at end of purge22 TSEN 7 failed c

30、lear initially on present or at end of purge23 TSEN 8 failed clear initially on present or at end or purge24 TSEN 1 failed clear during operation25 TSEN 2 failed clear during operation26 TSEN 3 failed clear during operation27 TSEN 4 failed clear during operation28 TSEN 5 failed clear during operatio

31、n29 TSEN 6 failed clear during operation2A TSEN 7 failed clear during operation2B TSEN 8 failed clear during operation2C TSEN 1 or SOH input failed blocked or bill jam during operation2D TSEN 2 or SOH input failed blocked or bill jam during operation or clamp present sensor failure2E TSEN 3 or SOH i

32、nput failed blocked or bill jam during operation2F TSEN 4 or SOH input failed blocked or bill jam during operation30 TSEN 5 or SOH input failed blocked or bill jam during operation31 TSEN 6 or SOH input failed blocker or bill jam during operation32 TSEN 7 or SOH input failed blocker or bill jam during operation33 TSEN 8 or