1、CiscoMCMTS常用指令集Cisco M-CMTS常用指令集1.Show diag1.1show diag 1/01.2show diag 1/0/02.show hw-module bay oir3.show controllers modular-cable3.1show controllers modular-cable 1/0/0 brief3.2show controllers modular-cable 1/0/0 sfp port 14.show controllers cable4.1show controllers cable 8/0/0 downstream4.2sho
2、w controllers cable 8/0/0 upstream5.show interface wideband-cable6.show hw-module bay6.1show hw-module bay 1/0/0 association wideband-channel 06.2show hw-module bay 1/0/0 config wideband-channel6.3show hw-module bay 1/0/0 counters wideband-channel 06.4show hw-module bay 1/0/0 mapping wideband-channe
3、l6.5show hw-module bay 1/0/0 config rf-channel 06.6show hw-module bay 1/0/0 counters rf-channel 07.show interface modular-cable8.show cable modem wideband9.show cable modem summary10.show cable modem primary11.show cable modem primary-channel12.show cable mac-domain downstream-service-group13.show c
4、able mac-domain cgd-associations14.Show hw-module bay 1/0/0 config rf-channel 0 verbose15.show hw-module bay 1/0/0 counters rf-channel16.Show hw-module bay 1/0/0 config wideband-channel17.Show cable clock18.Show cable clock dti counters1.Show diagTo verify that the Wideband SIP is powered on, use th
5、e show diag command. If show diag displays any output, the Wideband SIP is powered on. The show diag command provides a variety of information on the Wideband SIP. In the following example, the hardware type of the Wideband SIP is 2jacket-1 card.Router# show diag 1/0Slot/Subslot 1/0:2jacket-1 card,
6、0 portsCard is full slot sizeCard is analyzedCard detected 16:46:44 agoCard uptime 0 days, 16 hours, 46 minutes, 36 secondsCard idle time 0 days, 14 hours, 22 minutes, 34 secondsVoltage status: 3.3V Nominal 2.5V Nominal 1.5V Nominal 12V NominalEEPROM contents, slot 1/0:Hardware Revision : 1.0Top Ass
7、y. Part Number : 800-22843-04Board Revision : 01Deviation Number : 0-0Fab Version : 04PCB Serial Number : CSJ09030613RMA Test History : 00RMA Number : 0-0-0-0RMA History : 00CLEI Code :.If show diag displays no output, the Wideband SIP is not powered on.Router# show diag 1/0 / Displays no outputshow
8、 diag 1/0/0To display hardware and diagnostic information for a Wideband SPA, use the show diag command.Router# show diag 1/0/0Slot/Subslot/Port 1/0/0:24rfchannel-spa-1 card, 1 port + 1 redundant portCard is half slot sizeCard is analyzedCard detected 16:47:55 agoCard uptime: Not SupportedCard idle
9、time: Not SupportedVoltage status: 3.3V (+3.291) NOMINAL 2.5V (+2.495) NOMINAL1.2V (+1.201) NOMINAL 1.8V (+1.811) FIXEDEEPROM contents, slot 1/0/0:Hardware Revision : 1.0Boot Timeout : 500PCB Serial Number : CSJ09379726Part Number : 73-9597-03Part Number Revision : 05Fab Version : 03RMA Test History
10、 : 00RMA Number : 0-0-0-0RMA History : 00Deviation Number : 0Product (FRU) Number : SPA-24XDS-SFPVersion Identifier (VID) : V01Top Assy. Part Number : 68-2562-03Board Revision : 05CLEI Code :MAC Address : 0019.06a5.d9b2MAC Address block size : 1Manufacturing Test Data : 00 00 00 00 00 00 00 00Field
11、Diagnostics Data : 00 00 00 00 00 00 00 00Calibration Data : Minimum: 0 dBmV, Maximum: 0 dBmVCalibration values :Platform features : 00 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 00 0000 00 00 00 00 00 002. Show hw-module bay oirTo verify that the Wideband SPA is powered on, use th
12、e show hw-module bay oir command. If theOperational Status is “ok,” the Wideband SPA is powered on and operational.Router# show hw-module bay 1/0/0 oirModule Model Operational Status- - -bay 1/0/0 SPA-24XDS-SFP okIf show hw-module bay oir displays “admin down” in the Operational Status field, the Wi
13、deband SPAhas been administratively disabled.Router# show hw-module bay 1/0/0 oirModule Model Operational Status- - -bay 1/0/0 SPA-24XDS-SFP admin down3.Show controllers modular-cableWith Cisco IOS commands, the Wideband SPA and its Gigabit Ethernet ports are not considered standard user-configurabl
14、e interfaces and do not appear in the output of the show interfaces command. The Wideband SPA is a controller and the show controllers modular-cable command displays information about the SPA, its Gigabit Ethernet ports, installed SFP modules, wideband channels, and so on.The following example provi
15、des sample show controllers modular-cable output for the Wideband SPA located in slot 1, subslot 0, bay 0 of a Cisco uBR10012 router. In the output, the Gigabit Ethernet Port Selected field indicates that Port 1is the active Gigabit Ethernet port on the Wideband SPA.Router# show controllers modular-
16、cable 1/0/0 briefSPA 0 is presentstatus LED: greenHost 12V is enabled and is okay.Power has been enabled to the SPA.SPA reports power enabled and okay.SPA reports it is okay and is NOT held in reset.Gigabit Ethernet Port Selected : Port 1Receive Interface : In ResetReceive Interface : DisabledTransm
17、it Interface : Out of ResetTransmit Interface : EnabledPrimary Receive Clock : DisabledBackup Receive Clock : DisabledSFP Port 0 : 1000BASE-SX PresentTx Enabled , LOS Detected , TxFault Not DetectedLink Status Port 0 : DOWNSFP Port 1 : 1000BASE-T PresentTx Enabled , LOS Not Detected , TxFault Not De
18、tectedLink Status Port 1 : UPIn the preceding output, notice the following: The Gigabit Ethernet Port Selected field indicates the active Gigabit Ethernet port. For the active Gigabit Ethernet port, the SFP Port 1 field indicates the type of SFP module that ispresent. For the active Gigabit Ethernet
19、 port, the Link Status Port 1 field indicates whether the link is up.The Cisco Wideband SPA transmits data in a unidirectional manner only and does not receive data from devices connected to its active Gigabit Ethernet port.If the link for the active Gigabit Ethernet port is not up, check the follow
20、ing: The SFP module is correctly installed and matches the SFP module in the connected device. The cables to the Wideband SPA ports are correctly connected to a powered-on device. The cables to the Wideband SPA ports are not bent or damaged. A hardware failure has not occurred. For information, see
21、the “Performing Basic Troubleshootingon a Wideband SIP and Wideband SPA” section on page 5-19.Use the show controller modular-cable command with the sfp keyword to get more detailedinformation on the SFP modules installed in a Wideband SPA Gigabit Ethernet ports.Wideband Channel informationChannel R
22、F bitmap Police Info: Bytes Interval0 0x3 0 0 ms1 0xC 0 0 ms2 0x30 0 0 ms3 0xC0 0 0 ms4 0x300 0 0 ms5 0xC00 0 0 ms6 0x3000 0 0 ms7 0xC000 0 0 ms8 0x30000 0 0 ms9 0x0 0 0 ms10 0x0 0 0 ms11 0x0 0 0 msRF Channel informationModulation corresponds to : QAM 256Annex corresponds to : Annex BModulation Data
23、 :GE Interframe Gap = 12 , MPEG-TS Frames per pkt = 4SPA IP address = 0.0.0.0 SPA MAC Addr = 0012.001A.888BQAM Channel Rate Rate adjust State0 0 1 Enabled1 0 1 Enabled2 0 1 Enabled3 0 1 Enabled4 0 1 Enabled5 0 1 Enabled6 0 1 Enabled7 0 1 Enabled8 0 1 Enabled9 0 1 Enabled10 0 1 Enabled11 0 1 Enabled1
24、2 0 1 Enabled13 0 1 Enabled14 0 1 Enabled15 0 1 Enabled16 0 1 Enabled17 0 1 Enabled18 0 1 Enabled19 0 1 Enabled20 0 1 Enabled21 0 1 Enabled22 0 1 Enabled23 0 1 EnabledInterrupt CountsIdx Interrupt Register Interrupt Bit Total Count Masked:69 blz_sp_int_stat_reg_0 spi_train_vld 24 YES84 spa_brd_int_s
25、tat_reg sp_int_0 24 NO85 spa_brd_int_stat_reg scc_int 2 NO86 spa_brd_int_stat_reg phy1_int 1 NO87 spa_brd_int_stat_reg phy0_int 1 NO92 spa_brd_int_stat_reg temp1_int 2 NO93 spa_brd_int_stat_reg temp0_int 2 NO97 bm_int_stat_reg bm_spa_brd 26 NOTo display information about the SFP module in a Wideband
26、 SPA port, use the show controllersmodular-cable with the sfp keyword. In the following example, the information is for the SFP modulein port 1.Router# show controllers modular-cable 1/0/0 sfp port 1SFP in port 1SFP is presentSFP LOS is not detectedSFP TX FAULT is not detectedSFP TX is enabledID: SF
27、PExtended ID: 4Connector: LCSONET compliance: not specifiedGigabit Ethernet compliance: 1000BASE-SXFibre Channel link length: not specifiedFibre Channel transmitter technology: not specifiedFibre Channel transmission media: not specifiedFibre Channel speed: not specifiedEncoding: 8B10BBit Rate: 1300
28、 Mbps50 micron-multimode fiber supported length: 550 m62.5 micron-multimode fiber supported length: 270 mUpper bit rate limit: not specifiedLower bit rate limit: not specifiedDate code (yy/mm/dd): 05/02/23Vendor name: CISCO-AGILENTVendor OUI: 12499Vendor Part Number (PN): QFBR-5766LP Vendor Rev:Vend
29、or SN (SN): AGS090855CEOptions implemented:LOS SignalTX Fault SignalTX Disable SignalEnhanced options implemented: noneDiagnostic monitoring implemented: noneIdprom contents (hex):0x00: 03 04 07 00 00 00 01 00 00 00 00 01 0D 00 00 000x10: 37 1B 00 00 43 49 53 43 4F 2D 41 47 49 4C 45 4E0x20: 54 20 20
30、 20 00 00 30 D3 51 46 42 52 2D 35 37 360x30: 36 4C 50 20 20 20 20 20 20 20 20 20 03 52 00 B50x40: 00 1A 00 00 41 47 53 30 39 30 38 35 35 43 45 200x50: 20 20 20 20 30 35 30 32 32 33 20 20 00 00 00 C40x60: 00 00 06 C9 F0 FA 7C 01 B3 C8 41 6B 39 04 FC 850x70: BB 20 9E 00 00 00 00 00 00 00 00 00 B4 94 52 CC0x80: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF0x90: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FFState: InitalizedPhased InitializationPhase Reached: 4Phase Exit Code: 0Phase Read Offset: 04.Show contro
copyright@ 2008-2022 冰豆网网站版权所有
经营许可证编号:鄂ICP备2022015515号-1