太阳能光伏电池论文中英文资料对照外文翻译文献综述之欧阳体创编.docx

1、太阳能光伏电池论文中英文资料对照外文翻译文献综述之欧阳体创编光伏系统中蓄电池的充电保护IC电路设计时间：2021.02.03创作：欧阳体1.引言太阳能作为一种取之不尽、用之不竭的能源越来越受到重视。太阳能发电已经在很多国家和地区开始普及，太阳能照明也已经在我国很多城市开始投入使用。作为太阳能照明的一个关键部分，蓄电池的充电以及保护显得尤为重要。由于密封免维护铅酸蓄电池具有密封好、无泄漏、无污染、免维护、价格低廉、供电可靠，在电池的整个寿命期间电压稳定且不需要维护等优点，所以在各类需要不间断供电的电子设备和便携式仪器仪表中有着广泛的应用。采用适当的浮充电压，在正常使用(防止过放、过充、过流)时，

2、免维护铅酸蓄电池的浮充寿命可达1216年，如果浮充电压偏差5%则使用寿命缩短1/2。由此可见，充电方式对这类电池的使用寿命有着重大的影响。由于在光伏发电中，蓄电池无需经常维护，因此采用正确的充电方式并采用合理的保护方式，能有效延长蓄电池的使用寿命。传统的充电和保护IC是分立的，占用而积大并且外围电路复杂。目前，市场上还没有真正的将充电与保护功能集成于单一芯片。针对这个问题，设计一种集蓄电池充电和保护功能于一身的IC是十分必要的。2.系统设计与考虑 系统主要包括两大部分:蓄电池充电模块和保护模块。这对于将蓄电池作为备用电源使用的场合具有重要意义，它既可以保证外部电源给蓄电池供电，又可以在蓄电池过

3、充、过流以及外部电源断开蓄电池处于过放状态时提供保护，将充电和保护功能集于一身使得电路简化，并且减少宝贵的而积资源浪费。图1是此Ic在光伏发电系统中的具体应用，也是此设计的来源。 免维护铅酸蓄电池的寿命通常为循环寿命和浮充寿命，影响蓄电池寿命的因素有充电速率、放电速率和浮充电压。某些厂家称如果有过充保护电路，充电率可以达到甚至超过2C(C为蓄电池的额定容量)，但是电池厂商推荐的充电率是C/20C/3。电池的电压与温度有关，温度每升高1，单格电池电压下降4 mV，也就是说电池的浮充电压有负的温度系数-4 mV/。普通充电器在25处为最佳工作状态；在环境温度为0时充电不足；在45时可能因严重过充电

4、缩短电池的使用寿命。要使得蓄电池延长工作寿命，对蓄电池的工作状态要有一定的了解和分析，从而实现对蓄电池进行保护的目的。蓄电池有四种工作状态:通常状态、过电流状态、过充电状态、过放电状态。但是由于不同的过放电电流对蓄电池的容量和寿命所产生的影响不尽相同，所以对蓄电池的过放电电流检测也要分别对待。当电池处于过充电状态的时间较长，则会严重降低电池的容量，缩短电池的寿命。当电池处于过放电状态的时间超过规定时间，则电池由于电池电压过低可能无法再充电使用，从而使得电池寿命降低。 根据以上所述，充电方式对免维护铅酸蓄电池的寿命有很大影响，同时为了使电池始终处于良好的工作状态，蓄电池保护电路必须能够对电池的非

5、正常工作状态进行检测，并作出动作以使电池能够从不正常的工作状态回到通常工作状态，从而实现对电池的保护。3.单元模块设计3.1充电模块 芯片的充电模块框图如图2所示。该电路包括限流比较器、电流取样比较器、基准电压源、欠压检测电路、电压取样电路和逻辑控制电路。 该模块内含有独立的限流放大器和电压控制电路，它可以控制芯片外驱动器，驱动器提供的输出电流为2030 mA，可直接驱动外部串联的调整管，从而调整充电器的输出电压与电流。电压和电流检测比较器检测蓄电池的充电状态，并控制状态逻辑电路的输入信号。当电池电压或电流过低时，充电启动比较器控制充电。电器进入涓流充电状态，当驱动器截止时，该比较器还能输出2

6、0 mA左右，进入涓流充电电流。这样，当电池短路或反接时，充电器只能以小电流充电，避免了因充电电流过大而损坏电池。此模块构成的充电电路充电过程分为二个充电状态:大电流恒流充电状态、高电压过充电状态和低电压恒压浮充状态。充电过程从大电流恒流充电状态开始，在这种状态下充电器输出恒定的充电电流。同时充电器连续监控电池组的两端电压，当电池电压达到转换电压过充转换电压Vsam时，电池的电量己恢复到放出容量的70%90%，充电器转入过充电状态。在此状态下，充电器输出电压升高到过充电压Voc，由于充电器输出电压保持恒定不变，所以充电电流连续下降。当电流下降到过充中止电流Ioct时，电池的容量己达到额定容量的

7、100%，充电器输出电压下降到较低的浮充电压VF。3.2保护模块 芯片内部保护电路模块框图如图3所示。该电路包括控制逻辑电路、取样电路、过充电检测电路、过放电检测比较器、过电流检测比较器、负载短路检测电路、电平转换电路和基准电路(BGR)。 此模块构成的保护电路如图4所示。当芯片的供电电压在正常工作范围内，且VM管脚处的电压在过电流I检测电压之下，则此时电池处于通常工作状态，芯片的充放电控制端CO和DO均为高电平，这时芯片处于通常工作模式。而当电池放电电流变大，会引起VM管脚处的电压上升，若VM管脚处的电压在过电流检测电压Viov之上，则此时电池处于过电流状态，如果这种状态保持相应的过电流延时

8、时间tiov，芯片禁止电池放电，这时充电控制端CO为高电平，而放电控制端DO为低电平，芯片处于过电流模式，一般为了对电池起到更加安全合理的保护，芯片会对电池的不同过放电电流采取不同的过放电电流延时时间保护。一般规律是过放电电流越大，则过放电电流延时时间越短。当芯片的供电电压在过充电检测电压之上（VddVcu）时，则电池处于过充电状态，如果这种状态保持相应的过充电延时时间tcu芯片将禁止电池充电，此时放电控制端DO为高电平，而充电控制端CO为低电平，芯片处于过充电模式。当芯片的供电电压在过放电检测电压之下(VddR2分压后的输出电压，形成了欠压的正反馈。输出为高，欠压锁定，起到了保护作用。5.仿

9、真模拟结果与分析 本设计电路采用CSMC 0.6 m数字CMOS工艺对电路进行仿真分析。在对电路做整体仿真时，主要观察的是保护模块对电池的充放电过程是否通过监测Vdd电位和Vm电位而使芯片的CO端和DO端发生相应的变化。图7所示的整体仿真波形图是保护模块随着电池电压的变化从通常工作模式转换到过充电模式，然后回到通常工作模式，接着进入过放电模式，最后再回到通常工作模式。由于本设计处于前期阶段，各个参数还需要优化，只是提供初步的仿真结果。6.结论设计了一种集蓄电池充电与保护功能于一身的IC。利用此设计既可以减小而积，又可以减少外围电路元器件。电路同时采用了低功耗设计。由于此项目正在进行设计优化阶段

10、，完整的仿真还不能达到要求，还需要对各个模块电路进行优化设计。英语原文Design of a Lead-Acid Battery Charging and Protecting IC in Photovoltaic System1.IntroductionSolar energy as an inexhaustible, inexhaustible source of energy more and more attention. Solar power has become popular in many countries and regions, solar lighting has a

11、lso been put into use in many cities in China. As a key part of the solar lighting, battery charging and protection is particularly important. Sealed maintenance-free lead-acid battery has a sealed, leak-free, pollution-free, maintenance-free, low-cost, reliable power supply during the entire life o

12、f the battery voltage is stable and no maintenance, the need for uninterrupted for the various types of has wide application in power electronic equipment, and portable instrumentation. Appropriate float voltage, in normal use (to prevent over-discharge, overcharge, over-current), maintenance-free l

13、ead-acid battery float life of up to 12 16 years float voltage deviation of 5% shorten the life of 1/2. Thus, the charge has a major impact on this type of battery life. Photovoltaic, battery does not need regular maintenance, the correct charge and reasonable protection, can effectively extend batt

14、ery life. Charging and protection IC is the separation of the occupied area and the peripheral circuit complexity. Currently, the market has not yet real, charged with the protection function is integrated on a single chip. For this problem, design a set of battery charging and protection functions

15、in one IC is very necessary.2.System design and considerations The system mainly includes two parts: the battery charger module and the protection module. Of great significance for the battery as standby power use of the occasion, It can ensure that the external power supply to the battery-powered,

16、but also in the battery overcharge, over-current and an external power supply is disconnected the battery is to put the state to provide protection, the charge and protection rolled into one to make the circuit to simplify and reduce valuable product waste of resources. Figure 1 is a specific applic

17、ation of this Ic in the photovoltaic power generation system, but also the source of this design. Maintenance-free lead-acid battery life is usually the cycle life and float life factors affecting the life of the battery charge rate, discharge rate, and float voltage. Some manufacturers said that if

18、 the overcharge protection circuit, the charging rate can be achieved even more than 2C (C is the rated capacity of the battery), battery manufacturers recommend charging rate of C/20 C/3. Battery voltage and temperature, the temperature is increased by 1 C, single cell battery voltage drops 4 mV, n

19、egative temperature coefficient of -4 mV / C means that the battery float voltage. Ordinary charger for the best working condition at 25 C; charge less than the ambient temperature of 0 C; at 45 C may shorten the battery life due to severe overcharge. To make the battery to extend the working life,

20、have a certain understanding and analysis of the working status of the battery, in order to achieve the purpose of protection of the battery. Battery, there are four states: normal state, over-current state over the state of charge, over discharge state. However, due to the impact of the different d

21、ischarge current over-capacity and lifetime of the battery is not the same, so the battery over discharge current detection should be treated separately. When the battery is charging the state a long time, would severely reduce the capacity of the battery and shorten battery life. When the battery i

22、s the time of discharge status exceeds the allotted time, the battery, the battery voltage is too low may not be able to recharge, making the battery life is lower. Based on the above, the charge on the life of maintenance-free lead-acid batteries have a significant impact, while the battery is alwa

23、ys in good working condition, battery protection circuit must be able to detect the normal working condition of the battery and make the action the battery can never normal working state back to normal operation, in order to achieve the protection of the battery.3.Units modular design3.1The charging

24、 module Chip, charging module block diagram shown in Figure 2. The circuitry includes current limiting, current sensing comparator, reference voltage source, under-voltage detection circuit, voltage sampling circuit and logic control circuit. The module contains a stand-alone limiting amplifier and

25、voltage control circuit, it can control off-chip drive, 20 30 mA, provided by the drive output current can directly drive an external series of adjustment tube, so as to adjust the charger output voltage and current . Voltage and current detection comparator detects the battery charge status, and co

26、ntrol the state of the input signal of the logic circuit. When the battery voltage or current is too low, the charge to start the comparator control the charging. Appliances into the trickle charge state when the cut-off of the drive, the comparator can output about 20 mA into the trickle charge cur

27、rent. Thus, when the battery short-circuit or reverse, the charger can only charge a small current, to avoid damage to the battery charging current is too large. This module constitutes a charging circuit charging process is divided into two charging status: high-current constant-current charge stat

28、e, high-voltage charge status and low-voltage constant voltage floating state. The charging process from the constant current charging status, the constant charging current of the charger output in this state. And the charger continuously monitors the voltage across the battery pack, the battery pow

29、er has been restored to 70% to 90% of the released capacity when the battery voltage reaches the switching voltage to charge conversion voltage Vsam charger moves to the state of charge. In this state, the charger output voltage is increased to overcharge pressure Voc is due to the charger output vo

30、ltage remains constant, so the charging current is a continuous decline. Current down to charge and suspend the current Ioct, the battery capacity has reached 100% of rated capacity, the charger output voltage drops to a lower float voltage VF.3.2 Protection Module Chip block diagram of the internal protection circuit shown in Figure 3. The circuit includes control logic circuit, sampling circuit, overcha