1、AP3010DNAGN设置为普通无线路由器操作步骤华为AP3010DN-AGN无线AP设定为一般胖AP无线路由器模式操作步骤说明文档1,认识硬件除以上之外,还需要普通网线1条,电脑1台。2,所用到的软件操作系统xp或win7Xmanager4汉化版USB转COM线驱动TFTP软件3CDaemon汉化版AP升级固件的文档3,操作步骤: 第一步,复位AP,刷固件第二步,登录AP的WEB管理页面创建WIFI并建立DHCP第三步,创建WAN口并与LAN口关联下面分步详细说明准备软件,依次安装USB转COM驱动,Xmanager4汉化版,将TFTP软件3CDaemon汉化版复制到C盘,并变更文件夹名称为
2、TFTP,路径如C:TFTP ,把AP 的固件复制到C:TFTP目录中给AP接上12V2A的电源,此时不要接POE供电模块,注意!复位后将消除全部配置及密码。等启动完毕后,用尖锐物按下复位口10秒后松开,AP开始重新启动,AP的指示灯变为长亮启动状态,之后指示灯变为闪烁状态完成复位。完成复位后接上USB 转串口线,连接电脑USB口和AP的Console口,打开Xmanager4中的Xshell4,新建会话窗口选择SERIAL配置波特率9600及COM端口号正确连接成功后会显示Please configure the login password (/)Enter password:这是初次登录
3、要求设定密码,密码复杂度要求为英文加数字,最小8位,我们暂定密码hua88888填写两次密码后显示如下Enter password:Confirm password:这表示已经成功设定了管理密码,以上设定的密码仅限于连接Console口使用,和WEB管理界面不是同一个密码,WEB管理界面密码下面会提到。使用1条一般使用的网线,一端连接电脑,一端连接AP的ETH/PoE口,此时不要拔掉Console口上的串口线,不要拔掉12V电源,不要连接POE供电模块,配置电脑有线网卡的IP地址为子网掩码网关 DNS空白不填写,去我的电脑打开C:TFTP目录,打开点击设置TFTP服务器按钮,按照下图设置路径然
4、后回到Xshell4窗口,会显示Please check whether system data has been changed, and save data in timeConfiguration console time out, please press any key to log on是因为超时登出,需要重新填写密码登录,重新登录后按照以下脚本操作,整个过程不要关闭sys #键入Enter system view, return user view with Ctrl+Z.Huaweiap-mode-switch prepare #键入Info: Prepare is ok, U
5、se ap-mode-switch command to switch to fit ap.Huaweiap-mode-switch check #键入Info: Ap-mode-switch check ok.Huaweiap-mode-switch tftp #键入Info: Preparing to upgrade. Please wait a moment .Warning: System will reboot, if you want to switch to upgrade-assistant-package.Are you sure to execute these opera
6、tions Y/N:y #这里是提示整个过程会重启,键入yInfo: system is rebooting ,please wait.Try hardware rebooting. * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * Welcome To HUAWEI AP World UBoot V200R005 version-125 (Aug 1 2014 -
7、04:33:21)DRAM: 128 MBDDR data bus test is OK!Press c or C to Begin DDR Bus Test in 1 Seconds: 0 Flash: 32 MBPCIE: PCIe Clock 40MHzEthernet Mac: B4-15-13-F8-82-20Image: Current Bootup is B Image: Current Bootup is B Current master bootup parameter area is ABoot Kernel A Address: 0x9f3fb000Boot Kernel
8、 B Address: 0x9f840000Press j or J to stop Bus-Test in 1 seconds: 0Bus test starting.PCIE bus test OK.SPI bus test OK.DDR bus test OK.RGMII bus test OK.Bus test ending.Save Bus Test Result SuccessfulPress f or F to stop Auto-Boot in 3 seconds: 0 Uncompressing Kernel Image . OKStarting kernel .Bootin
9、g Atheros AR934xinit_bsp_adapter .OK.mm_init .OK.sched_init .OK.softirq_init .OK.console_init .OK.thread_info_cache_init .OK.fork_init .OK.dbg_late_init .OK.imv_init_complete .OK.Linux version -WR_standard (gcc version (Sourcery CodeBench Lite ) #2 PREEMPT Fri Nov 7 17:34:15 CST 2014flash_size passe
10、d from bootloader = 32 MBarg 1: console=ttyS0,9600arg 2: root=/dev/mtdblock10arg 3: rootfstype=squashfsarg 4: init=/sbin/initarg 5: mtdparts=ath-nor0:512k(BiosA),128k(BootupA),128k(BootupB),128k(BootEnv),128k(BoardData),12288k(SysImageA),3072k(configA),512k(BiosB),128k(ResultA),128k(ResultB),12288k(
11、SysImageB),3072k(configB),256k(ArtArgs);arg 6: mem=126Math_sys_frequency: cpu apb,ddr apb,cpu-480MHZ,ddr-400MHZ,ahb-240MHZZone PFN ranges: Normal 0x00000000 - 0x00007e00Movable zone start PFN for each nodeearly_node_map1 active PFN ranges 0: 0x00000000 - 0x00007e00Built 1 zonelists in Zone order, mo
12、bility grouping on. Total pages: 32004Kernel command line: console=ttyS0,9600 root=/dev/mtdblock10 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:512k(BiosA),128k(BootupA),128k(BootupB),128k(BootEnv),128k(BoardData),12288k(SysImageA),3072k(configA),512k(BiosB),128k(ResultA),128k(ResultB),1228
13、8k(SysImageB),3072k(configB),256k(ArtArgs); mem=126M Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytesFWD_MEM: aligned address FWD_MEM: 02000000 FWD_MEM: Allocating 21MB (5568 pages) of memory at addr the pci irq_bas
14、e value: 70plat_time_init:.doneMount-cache hash table entries: 512Registering WDT.doneath_pcibios_init: bus 0PCI init:.doneath_pcibios_init(234): PCI 0 CMD write: 0x356registering PCI controller with io_map_base unsetbio: create slab at 0SCSI subsystem initializedpcibios_map_irq: IRQ 70 for bus 0ath
15、_init_ioctl.doneinit_vdso successfullmtd: no mtd-idath_flash_init.donemii_bus 0 successed to registerRegistering OTP.doneRegistering Clock Switch Interface.donestarting pid 42, tty : /etc/rcSMIMC_KERNEL: Module init.enable_rx 1250: init_phy_eee: control = 0x1000FatAP3X10XN_V200R005 100% |*| 21377k 0
16、0:00:00 ETA. #这里开始上传固件,之后继续重启.Error: Upgrade failed due to a type mismatch.starting pid 149, tty : /sbin/swapoff -acant run /sbin/swapoff: No such file or directorystarting pid 150, tty : /bin/umount -a -rumount: tmpfs busy - remounted read-onlyumount: none busy - remounted read-onlyumount: /proc bu
17、sy - remounted read-onlyThe system is going down NOW!Sent SIGTERM to all processesSent SIGKILL to all processesRequesting system rebootRestarting system.Try hardware rebooting. * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
18、 * * * * * * * * Welcome To HUAWEI AP World UBoot V200R005 version-125 (Aug 1 2014 - 04:33:21)DRAM: 128 MBDDR data bus test is OK!Press c or C to Begin DDR Bus Test in 1 Seconds: 0 Flash: 32 MBPCIE: PCIe Clock 40MHzEthernet Mac: B4-15-13-F8-82-20Image: Current Bootup is A Image: Current Bootup is A
19、Current master bootup parameter area is BBoot Kernel A Address: 0x9f3fb000Boot Kernel B Address: 0x9f840000Press j or J to stop Bus-Test in 1 seconds: 0Bus test starting.PCIE bus test OK.SPI bus test OK.DDR bus test OK.RGMII bus test OK.Bus test ending.Save Bus Test Result SuccessfulPress f or F to
20、stop Auto-Boot in 3 seconds: 0 Uncompressing Kernel Image . OKStarting kernel .Booting Atheros AR934xinit_bsp_adapter .OK.mm_init .OK.sched_init .OK.softirq_init .OK.console_init .OK.thread_info_cache_init .OK.fork_init .OK.dbg_late_init .OK.imv_init_complete .OK.Linux version -WR_standard (gcc vers
21、ion (Sourcery CodeBench Lite ) #1 PREEMPT Fri Aug 1 04:16:06 CST 2014flash_size passed from bootloader = 32 MBarg 1: console=ttyS0,9600arg 2: root=/dev/mtdblock5arg 3: rootfstype=squashfsarg 4: init=/sbin/initarg 5: mtdparts=ath-nor0:512k(BiosA),128k(BootupA),128k(BootupB),128k(BootEnv),128k(BoardDa
22、ta),12288k(SysImageA),3072k(configA),512k(BiosB),128k(ResultA),128k(ResultB),12288k(SysImageB),3072k(configB),256k(ArtArgs);arg 6: mem=126Math_sys_frequency: cpu apb,ddr apb,cpu-480MHZ,ddr-400MHZ,ahb-240MHZZone PFN ranges: Normal 0x00000000 - 0x00007e00Movable zone start PFN for each nodeearly_node_
23、map1 active PFN ranges 0: 0x00000000 - 0x00007e00Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32004Kernel command line: console=ttyS0,9600 root=/dev/mtdblock5 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:512k(BiosA),128k(BootupA),128k(BootupB),128k(BootEnv),128k(Board
24、Data),12288k(SysImageA),3072k(configA),512k(BiosB),128k(ResultA),128k(ResultB),12288k(SysImageB),3072k(configB),256k(ArtArgs); mem=126M Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytesFWD_MEM: aligned address FWD_MEM: 02000000 FWD_MEM: Allocating 21MB (5568 pages) of memory at addr the pci irq_base value: 70plat_time_init:.doneMount-cache hash table entries: 512Registering WDT.doneath_pcibios_init: bus 0PCI init:.doneath_pcibios_init(234): PCI 0 CMD write: 0x356registering PCI controller with io_map_base u
copyright@ 2008-2022 冰豆网网站版权所有
经营许可证编号:鄂ICP备2022015515号-1