AB变频器快速调试.docx

1、AB变频器快速调试 Last updated on the afternoon of January 3, 2021AB变频器快速调试 编辑参数如下1.上电时LCD显示器显示为:Output Freq S 按一次SEL键显示组参数编号及字母.按上下键改变组菜单(Basic Display:b基本显示.Basic Pr0gram :P基本编程.Terminal Block:T端子.Communications:C通信.Advanced progran:A高级编程，Aux Relay Cord: R=Aux Relay Display:d高级显示)。2.按SEL键进入某组菜单，该组中上次查看时的参

2、数编号将会闪烁。按上下键可选择主菜单功能，先选择基本显示(Display Groupb)参数按下SEL进入:b001:输出频率 002：命令频率003：输出电流 ：004输出电压 005：直流母线电压006：变频器状态 007：故障代码1 008：过程显示 010：输出功率 011：已用电MVV 012：运行时间 013：转矩电流 014：变频器温度 015：已用电KW 以上参数是变频器自动默认不用修改。3.按上下键可选择主菜单功能，先选基本编程Basic Progran Group按下SEL进入注：这些参数要根据实用的值来进行设定 P031：motor NP Volts(电动机铭牌电压) P

3、032：motor NP Hertz (电动机铭牌频率) P033：motor OL current(电动机额定电流 )P034：minimum Freq(最小频率 ) P035：maximum Freq(最大频率)50HZ P036：Start Source(起动源)2-wire 002 P037：Stop mode(停止模式)coast 005 P038:Speed Reference(速度基准值)Analog in1 002 P039:Accel Timel(加速时间为15秒)Sec P040：Decel Timel(减速时间为10秒)Sec P041：Reset to Defalts复

4、位为默认值工Ready/Zdle 000 P042：Auto mode(自动模式) NO Function 003 P043：Motor OL Ret(电机过载值存储)Disabled 0004.按上下键可选择主菜单功能，先选端子 Terminal Block Group按下SEL进入T051:Terminal Block(数字量输入1选择) Digital in1 sel T052:Digital In2 sel(数字量输入2选择)Local 003 T053:Digital In3 sel(数字量输入3选择) Clear Fault 010 T054:Digital In4 sel(数字量

5、输入4选择) Comm port 004 T055:Relay out1 sel (继电器输出1选择)Ready/Fault 000 T056:Relay out1 Level (继电器输出1幅值) T058:Relay 1 on Time(继电器1接通On时间) sec T059:Relay 1 off Time(继电器1断开Off时间) sec T060:Relay out 2 sel(数字量输出2选择) motor Running 002 T061:Relay out 2 Level (继电器输出2幅值) T063:Relay 2 on Time(继电器2接通On时间) sec T064

6、:Relay 2 off Time(继电器2断开Off时间) sec T065: Opto out sel (光电耦合输出选择)At Frequency 001 T066: Opto out Level(光电耦合输出幅值) T068: Opto out Logic (光电耦合输出逻辑) T069: Analog In 1 Sel(模拟量输入1选择) 4-20mA 001 T070: Analog In 1 LO(模拟量输入1下限) % T071: Analog In 1 Hi(模拟量输入1上限)% T072: Analog In 1 Loss(模拟量输入1丢失)Disabled 000 T07

7、3: Analog In 2 Sel(模拟量输入2选择) 0-10V 002 T074: Analog In 2 LO(模拟量输入2下限) % T075: Analog In 2 Hi(模拟量输入2上限)% T076: Analog In 2 Loss(模拟量输入2丢失)Disabled 000 T077: Sleep-wake sel (休眠-唤醒选择) Disabled 000 T078: Sleep-Level (休眠等级) 10% T079: Sleep-Time (唤醒时间) SEC T080: wake-Level (唤醒等级) 15% T081: wake-Time (唤醒时间)

8、 SEC T082:Analog out 1 sel (模拟量输出1选择) outFreq 0-10V 000 T083:Analog out 1 High (模拟量输出1上限)100% T084:Analog out 1 setpt(模拟量输出1设定点)% T085:Analog out 2 sel (模拟量输出2选择) outcurr 0-10V 001 T086:Analog out 2 High (模拟量输出2上限)100% T087:Analog out 2 setpt(模拟量输出2设定点)% T088:Anlg Loss Delay (模拟量丢失延时) SEC T089:Analo

9、g In Filter (模拟量输入上限)05. 按上下键可选择主菜单功能，先选通信语言Communications Group按下SEL进入 C101:Language(通信语言)001 EnglishC102:Comm Format(通信格式)C103:Comm Data Rate(通信数据速率)003 9600C104:Comm Node Addr(通信节点地址)C105:Comm Loos Action(通信丢失动作)C106:Comm Loos Time(通信丢失时间)C107:Comm Write Mode(通信写模式)C108:Start Source2(通信起动命令源2)6.按

10、上下键可选择主菜单功能，先选高级编程Advanced Program Group 按下SEL进入 A141:Advanced Program Group(消防强制输入频率)Purge Frequency A142:Internal Freq(内部频率)60HzA143:Preset Freq0(预置频率0)A144:Preset Freq1(预置频率1)A145:Preset Freq2(预置频率2)A146:Preset Freq3(预置频率1)A147:Accel Time 2(加速时间2) SecA148:Decel Time 2(减速时间2) SecA149:S Curve%(S曲线%

11、)20%A150:PID Trim Hi(PID整定上限)60HZA151:PID Trim LO(PID整定下限)A152:PID Ref sel(PID基准值选择)PID setpoint 001A153:PID Feedback sel (PID反馈值选择)Anaiog In1 000 A154:PID Prop Gain(PID比例增益) 1A155:PID Integ Time(PID积分时间) SscA156:PID Diff Rate(PID微分速率) 1/SecA157:PID Setpoint(PID设置点)50%A158:PID Deadband(PID死区)%A159:P

12、ID Preload(PID预负载)A160:PID Process Factor(PID过程因数)A163:Auto Rstrt Tries(自动重新起动尝试)0A164: Auto Rstrt Delay(自动重新起动延时) SecA165:Start At PowerUp (上电起动)Disabled 000 A166:Reverse Disable (反向禁止)REV Disabled 001A167:Flying Start En (飞速起动使能)Disabled 000A168:Pwm Frequency(PWM频率) A169:Pwm Mode(PWM模式) 2-Phase 00

13、1A170:Boost select(升压选择) 004A171:Start Boost(起动升压) %A172:Break Voltage(转折电压)25%A173:Break Frequency(转折频率)A174:Maximum Voltage(最大电压)460 VACA175:slip Hertz FLA(满载滑差频率补偿)A176:DC Brake Time(直流制动时间) SECA177:DC Brake Level(直流制动幅值)A178:DC Brk TimeStrt(起动时直流制动时间)A179:Current Limit 1(电流限幅1)A180:Current Limit

14、 2(电流限幅2)A181:Motor Select(电动机过载选择)A182:Drive OL Mode(变频器过载模式)A183:SW Current Trip(软件电流跳闸)A184:Load Loss Level(负载丢失幅值)A185:Load Loss Time (负载丢失时间)A186:Stall Fault Time (堵转故障时间)A187:Bus Reg Mode (总线调节模式)A188:Skip Frequency1(跳变频率1)A189:Skip Freq Band1(跳变频率宽带1)A190:Skip Frequency2(跳变频率2)A191:Skip Freq

15、Band2(跳变频率宽带2)A192: Skip Frequency3(跳变频率3)A193:Skip Freq Band3(跳变频率宽带3)A194:Compensation(补偿)A195:Reset Meters(测量复位)A196:Testpoint Sel(测试点选择)A197:Fault Clear(故障清除)A198:Program Lock (编程锁定) A199:Motor NP Poles(电动机铭牌极对数)A200:Motor NP FLA(电动机铭牌电流)7.按上下键可选择主菜单功能，先选辅助继电器Aux Relay Card Group 按下SEL进入 R221:Re

16、lay Out3 Sel (继电器输出3选择) R222:Relay Out3 Level (继电器输出3幅值) R224:Relay Out4 Sel (继电器输出4选择) R225:Relay Out4 Level (继电器输出4幅值) R227:Relay Out5 Sel (继电器输出5选择) R228:Relay Out5 Level (继电器输出5幅值) R230:Relay Ou63 Sel (继电器输出6选择) R231:Relay Out6 Level (继电器输出6幅值) R233:Relay Out7 Sel (继电器输出7选择) R234:Relay Out7 Leve

17、l (继电器输出7幅值) R236:Relay Out8 Sel (继电器输出8选择) R237:Relay Out8 Level (继电器输出8幅值) R239:Aux Motor Mode (辅助电机模式) R240:Aux Motor Qty(辅助电机数量) R241:Aux 1 Start Freq(辅助1起动频率) R242:Aux 1 Stop Freq(辅助1停止频率) R243:Aux 1 Ref Add(辅助1频率增加) R244:Aux 2 Start Freq(辅助2起动频率) R245:Aux 2 Stop Freq(辅助2停止频率) R246:Aux 2 Ref Ad

18、d(辅助2频率增加) R247:Aux 3 Start Freq(辅助3起动频率) R248:Aux 3 Stop Freq(辅助3停止频率) R249:Aux 3 Ref Add(辅助3频率增加) R250:Aux Start Deiay(辅助起动延时) R251:Aux Stop Deiay(辅助停止延时) R252:Aux Prog Delay(辅助控制延时) R253:Aux AutoSwap Tme (辅助自动切换延时) R254:Aux AutoSwap Lvl (辅助自动切阀值) 8.按上下键可选择主菜单功能，先选辅助继电器Advanced Display Group 按下SEL

19、键进入 d301:Control Source(控制源) d302:Control Source(控制输入状态) d303:Comm Display Group(通讯状态) d304:PID Setpnt Displ(PID设定点显示) d305:Analog In 1(模拟量输入1) d306:Analog In 2(模拟量输入2) d307:Fault 1 Code(故障代码1) d308:Fault 2 Code(故障代码2) d309:Fault 3 Code(故障代码3) d310:Fault 1 Time-hr(故障时间1-小时) d311:Fault 1 Time-min(故障时

20、间1-分钟) d312:Fault 2 Time-hr(故障时间2-小时) d313:Fault 2 Time-min(故障时间2-分钟) d314:Fault 3 Time-hr(故障时间3-小时) d315:Fault 3 Time-min(故障时间3-分钟) d316:Elapsed Time-hr(消逝时间-小时) d317:Elapsed Time-min(消逝时间-分钟) d318:Output Powr Fctr(输出功率因数) d319:Testpoint Data(测试点数据) d320:Control SW Ver(控制版软件版本) d321:Drive Type(变频器类型) d322:Output Speed(输出速度) d323:Output RPM(输出速度) d324:Fault Frequency(输出速度) d325:Fault Current(输出速度) d326:Fault Bus Volts(输出速度) d327:Status Fault(输出速度)