48V75Ah钛酸锂电池规格书.docx

1、48V75Ah钛酸锂电池规格书Lithium Titanate Battery Specification钛酸锂电池规格书Model产品型号48V/7.5AhSpecification规格书编号Vision版次Date日期Prepared By/Date拟定Checked By/Date审核Approved By/Date批准Customer Signature客户回签栏Amendment Records修正记录Edition版本Description记述Prepared by编制Approved by批准Date日期A1第一版2017-09-061Scope使用围This specifica

2、tion describes the basic performance, technical requirement, testing method,warning and caution of lithium titanate battery pack. The specification only applies to the battery packs made byBetter Energy Saving Technology Co., Ltd.本标准规定了钛酸锂电池组的基本性能、技术要求测试方法与注意事项。本标准只适用于普兰能源科技所生产的钛酸锂电池组。2Product Model

3、产品型号IFR18650-20S5P（18650-1500mAh）3. Product Specification产品技术规格Number序号Content容Conventional Parameter常规参数Remark备注1Capacity容量Rated Capacity: 7.5Ah标称容量：7.5AhStandardDischarge Current:10A标准放电电流：10ADischarge Cut-off Voltage:30V放电截止电压：30VMin Capacity: 7.5Ah最小容量（Min.）：7.5Ah2Nominal Voltage标称电压48V3End of C

4、harge Voltage充电最高电压54V4Charge Mode充电方式CC、CV5Charging Current充电电流20A6Charging Cut-off Current充电截止电流0.05C7Charging Time充电时间2540min8Over-Charge VoltageProtection 模组过充电压保护540.025V9Discharging Current正常放电电流10A10Maximum ContinuousDischarging Current持续最大工作电流15A11Over-discharge VoltageProtection模组过放电压保护300.

5、1V12Over-Current DischargeProtection过流保护25A13Short Circuit Protection短路保护Any Protection有保护14Short Circuit ProtectionRelease短路保护恢复Disconnect Load断开负载Recovery Time: 3s恢复时间：3秒15Temperature Protection温度保护60516Factory Voltage出厂电压42V17Dimension 尺寸Long（长）= 3552mmWidth（宽）= 1602mmHigh（高）=902mmStructural Dime

6、nsions Are Detailed in Page 10结构尺寸详见第10页18Weight重量8kg19Operation TemperatureRange工作温度围Charge: -3045充电：-3045Discharge: -4060放电：-40606025%R.H. Bare Cell单体电池储存湿度围：6025%R.H.20Storage TemperatureRange储存温度围1 Month（一个月）：-20 453 Month（三个月）：-20 451 Year（一年）：-20 206025%R.H. at the ShipmentState出货状态时的湿度围：6025%

7、R.H.21Cycle Life循环寿命Tested at temperature of205.(1)Be charged at 15A to limited charge voltage 54V and change to charge at constant voltage till current no more than 0.05C. Stop charging;(2) Rest 5-10min, and then discharge at 10A until end voltage 30V.在环境温度205的条件下进行。（1）以15A电流充电，当电池组端电压达到充电限制电压54V时，

8、改为恒压充电，直到充电电流小于或等于0.05C，停止充电；（2）搁置5min-10min，然后以10A电流放电至终止电压30V。3000 Cycles Higher than 80%of the InitialCapacities of the Cells3000次初始容量80%22Vibration振动The fully charged at10A battery pack is fixed to the vibration platform; vibrate 30 minutes on each direction of X, Y and Z, amplitude of 1.5mm,fre

9、quency from 10Hz to 50Hz, change 1Hz/min.电池组以10A充满电后固定在振动台上；沿X、Y和Z三个方向各振动30分钟，振幅1.5mm，频率为10Hz50Hz，每分钟变化1Hz。Battery appearance has no distortion,explosion,fire, smoke and leaking.Battery voltage should be no less than 48V.电池组外观应无明显损伤、漏液、冒烟或爆，电池电压应不低于48V。4Battery Performance Test Criterion 电池性能测试规4.1

10、Appearance 外观There shall be no such defects such as scratch, flaw, crack, rust and leakage, which may adversely affect commercial value ofbattery.电池外观应没有划痕、破裂、污迹、生锈、漏液等影响市场的缺陷存在。4.2 Measurement Apparatus测量仪器(1)Dimension Measuring Instrument尺寸测量器具The dimension measurement shall be implemented by inst

11、ruments with equal or more precision scaleof 0.1mm.尺寸测量器具的精度等级应不小于0.1mm。(2)Voltmeter电压表Standard class specified in the national standard or more sensitive class. The inner impedanceismore than 10k/V.国家标准或采用灵敏度更高的，阻不小于10k/V。(3) Ammeter电流表Standard class specified in the national standard or more sensi

12、tive class. Total external resistanceincluding ammeter and wire is less than 0.01.国家标准或采用灵敏度更高的，包括电流表与电线在的总阻应小于0.01。(4) Impedance Meter阻抗计Impedance shall be measured by a sinusoidal alternating current method (AC 1kHz LCR meter).采用正弦交流法测试阻抗（AC 1kHz LCR meter）4.3 Testing Condition 测试条件Temperature 255

13、; Relative humidity:6020%; Atmosphere pressure:86106Kpa温度：255；相对湿度：6020%；大气压强：86106Kpa4.4 Battery test requirements 电池测试要求Standard charge: under environment temperature as 255,charging as 15A when the voltage of the battery reach the limited point, then change to constant voltage charging till the c

14、harging current less or equal to 0.05C .The longest charging time should be less than 40min.标准充电：在环境温度255下，以15A充电，电池端电压达到充电限制电压时，改为恒压充电，直到充电电流小于或等于0.05C，最长充电时长不大于40min。5Hazard Warning危险警告(1)Forbid short-circuit batteries禁止电池短路Do not touch the plus and minus contacts with metals. Do not put the batte

15、ry with metal element together in either storage or movement. If the battery is short-circuit, it carries magnified current, which will cause damage and make the battery heat, smoke, distort or burning.不要让电池的正负极用金属连接，也不要将电池与金属片放在一起存储和移动，如果电池被短路，将会有超大电流通过，将会损坏电池，造成电池发热、冒烟、变形或燃烧。(2) Forbid disassembli

16、ng batteries禁止拆装电池The battery has protective component and circuit internally to avoid danger. Mishandling such as improper disassembly will destroy its protective function and make it heat,smoke, distort or burning.电池部具有保护结构和保护电路可以避免发生危险。不合适的拆装会破坏保护功能，将会造成电池发热、冒烟、变形或燃烧。(3) Forbid heating and burnin

17、g the battery严禁加热和焚烧电池If heating or burning the battery, it will caused the isolated element in the battery dissolved, protection function stopped or the electrode burning, over heat, which will make the battery heat, smoke, distort or burning.加热和焚烧电池将会造成电池隔离物的融化、安全功能丧失或电解质燃烧，过热就会使电池发热、冒烟、变形或燃烧。(4)

18、Avoid using the battery near the heat 避免在热源附近使用电池Do not use the battery near the fire and stove, or over 60, and overheating will cause the battery internal short-circuit and make it heat, smoke, distort or burning.不要在火源、烤炉附近或超过60的环境中使用电池，过热将会导致电池部短路，使电池发热、冒烟、变形或燃烧。(5) Forbid bathing the battery禁止弄湿

19、电池Do not dampen the battery, or even immerse it in the water, which will cause internal protection circuit and lose its function or cause abnormal chemical reactions, which will lead to heating, smoking, distortion or burning.不要弄湿电池，更不能将电池投入水中，否则会造成部保护电路和功能丧失与发生不正常的化学反应，电池有可能发热、冒烟、变形或燃烧。(6) Forbid d

20、amaging battery禁止破坏电池Do not allow damaging the battery with the metals gouged, forged or dropped etc., otherwise, it will cause over-heated, distort, smoke, or burning.禁止用金属凿入电池、捶打或摔打电池或其他方法破坏电池，否则会造成电池发热、变形、冒烟或燃烧。(7) Forbid directly welding on battery 禁止在电池主体上焊接Over-heated will cause the isolated e

21、lement dissolved in the battery and lose protective function its cycle life, even will cause over-heat, distort, smoke or burning.过热将会造成电池隔离物的熔化、安全保护功能丧失，甚至将引起发热、冒烟或燃烧。6.Product Renderings产品效果图图1产品效果图图2 产品尺寸图图3 VH-2P端子实物图7电池管理系统 BMS主要功能（1）电池故障分析与报警信号输出BMS设置了系统自诊断功能，系统上电后对电压、温度、通讯、存储器、部通讯等部件进行检测，并提供相

22、应的故障代码与等级。过充报警触点输出：过充（任何单体电池电压上升到预设阈值以上）。过放报警触点输出：过放（总电压低于设定值；单体电池电压低于设定值）。信号报警，当出现以下情况时模块通过CAN总线将报警信号发送至显示屏，显示屏显示报警信息：单体电池过高；单体电池过低；电池组总电压过高；电池组总电压过低；电池容量过低；电池容量过高；单体电池温度过高；通信异常；电池管理系统异常等。（2）充电管理功能BMS与充电机采用CAN通讯，根据确定的充电管理协议由BMS对充电机进行充电控制。（3）电池组工作电流检测通过分流器检测电池组的充放电电流，在电流异常（超过阈值）时,通过CAN总线发送故障数据，采集误差小

23、于1%(30A以下误差小于1A)。（4）电池组SOC的估算通过分流器对电流采样，完成电流的测量，包括SOC计量和SOC故障等级报警，SOC计算误差小于10%。（5）电池单体电压检测功能BMS能准确、实时测量每个单体电池的电压，电压采集精度5mV，平均采样周期50ms，从而精确与时监控电池在使用过程中的状态与变化，有效地防止电池的不正当使用。单体电压测量回路在待机或休眠模式下，漏电不超12A。（6）电池温度检测BMS能够准确、同步的测量各个电池的温度值，测量误差2（-40+85）。（7）电池均衡功能在充电过程中，可以按照协定的均衡管理控制策略对电芯进行均衡管理功能，进而减少电池在使用过程的不一致性，提高整组电池的使用性能。均衡电流100mA。表2 BMS主要技术参数序号项目额定参数备注1模块工作电压48.0V2总电压采集精度0.5%3总电流采集精度1.0%4工作温度-40+855存储温度-40+1256绝缘电阻检测误差10.0%7休眠电流1.0mA8绝缘等级500V电压下绝缘大于200M