EDUCATEELBFSV5R9.docx
《EDUCATEELBFSV5R9.docx》由会员分享,可在线阅读,更多相关《EDUCATEELBFSV5R9.docx(20页珍藏版)》请在冰豆网上搜索。
EDUCATEELBFSV5R9
ElectricalLibrarian
DetailedSteps
TableofContents
Definingacomponentscatalog4
Step1:
Definingthecatalogstructure4
Step2:
Addingtheelectricalpropertiestotheequipment5
Step3:
Addingtheelectricalpropertiestotheshell6
Step4:
Addingtheelectricalpropertiestothefillerplug7
Step5:
Addingtheelectricalpropertiestothedeviceconnector8
Step6:
Addingtheelectricalpropertiestothecontacts9
Step7:
Addingtheelectricalpropertiestotheharnessconnector9
Step8:
Storethecomponentsintothecatalog10
Step9:
Definetheassembly10
DefineanElectricalEquipment11
Step1:
Definingthegeometry11
Step2:
Definingtheequipment12
Step3:
Definingthecavities12
Createanewcatalogandimportalistofwires13
Step1:
Creatingacatalog13
Step2:
Importingasetofwires14
Createatotallydefinedequipment15
Step1:
Importthecomponents15
Step2:
Connectthecomponents16
Createanewwirewithitsproperties17
DefineaSupport18
Step1:
Definingthegeometry18
Step2:
DefiningtheSupport19
DefineanadaptableSupport20
Step1:
Electricalsupport20
Step2:
DefiningtheSupportparameters21
Step3:
Assembly22
Step4:
CreatingaGeometricalBundle23
Step5:
Otheradaptativesupport24
Definingacomponentscatalog
Youwillcreateyoucomponentsandyouassembliesandyouwilladdthemintoyoucatalog.
Step1:
Definingthecatalogstructure
1.Openthecatalog“CATELB_EMPTY_COMPONENTS_CATALOG.catalog”
2.Selectthefunction“AddFamily”andgivethenewfamilythename“Equipments”.
3.
Repeatstep2withfollowingfamilynames“HarnessConnectors”,“DeviceConnectors”,“Shells”,“BackShells”,“Contacts”,“FillerPlugs”,“Wires”.
4.Savethecatalogwiththename“CATELB_COMPONENTS_CATALOG_WITH_FAMILIES.catalog”
Step2:
Addingtheelectricalpropertiestotheequipment
5.Openthecomponent“CATELB_BASIC_EQT_WITH_CONN.CATPart”
6.Selectthe“ElectricalPartDesign”workbench
7.Selectthe“DefineEquipment”functionandclickontheproduct
8.Givethenewequipmentthename“CATELB_BASIC_EQT_WITH_CONNECTOR_ELEC
9.Selectthefunction“DefineCavity”.Clickontheequipment.
10.Givethenewcavitythename“cav1”
11.Selecttheholeasarepresentation.
12.Selectthefaceatthebottomoftheholeasacontactsurface.
13.Selectthelineoutofthecavityfrontsurfaceascoincidence.
14.Savethenewequipmentwiththename“CATELB_BASIC_EQT_WITH_CONNECTOR_ELEC.CATPart”
Step3:
Addingtheelectricalpropertiestotheshell
15.Openthecomponent“CATELB_BASIC_SHELL.CATPart”
16.Makesureyouareusingthe“ElectricalPartDesign”workbench
17.Selectthefunction“DefineShell”andclickonthegeometry.
18.Givethenewshellaname.
19.Selectthefunction“DefineCavity”
20.Clickontheshell
21.Givethenewcavityaname,clickonthefirstholeasarepresentation.Clickonthesurfaceatthebottomoftheholeasacontactsurfaceandclickonthelineasacoincidence.
22.Repeatsteps5to7fortheothertwocavities.
23.Selectthefunction“DefineCavityConnectionPoint”andclickontheshell.
24.Giveitthename“ccppt1”
25.Selectthesurfacethatisgoingtobeconnectedtotheequipment(ontheback)asarepresentation.
26.Selectthelineasacoincidence.
27.Selectanedgeoftheshellfortheorientation.
28.Savetheshellwiththename“CATELB_BASIC_SHELL_ELEC.CATPart”.
Step4:
Addingtheelectricalpropertiestothefillerplug
29.Openthecomponent“CATELB_FILLER_PLUG2.CATPart”
30.Selectthefunction“DefineFillerPlug”andclickonthegeometry.
31.Selectthefunction“DefineCavityConnectionPoint”andclickonthegeometry
32.Givetheccpthename“ccpt1”
33.Selectthebacksideofthefillerplugasarepresentation
34.Selectthelineasacoincidence
35.Selectanedgeofthefillerplugfortheorientation.
Step5:
Addingtheelectricalpropertiestothedeviceconnector
36.Openthecomponent“CATELB_BASIC_DEV_CONNECTOR.CATPart”
37.Selectthefunction“DefineConnector”andclickonthegeometry
38.Givethenewconnectorthename“CATELB_BASIC_DEV_CONNECTOR_ELEC”
39.Selectthefunction“DefineCavityConnectionPoint”andclickonthegeometry
40.Giveitthename“ccpt1”,selectthebacksidefortherepresentation,thelineasacoincidenceandanedgefortheorientation.
41.Selectthefunction“DefineConnectorConnectionPoint”andclickonthegeometry
42.Giveitthename“ccpt1”,selectthefrontsidewiththetwoholesfortherepresentation,thelineasacoincidenceandanedgefortheorientation.
43.Savetheobjectwiththenewname.
Step6:
Addingtheelectricalpropertiestothecontacts
44.Openthecomponent“CATELB_CONTACT.CATPart”
45.Makesureyouareusingthe“ElectricalPartDesign”workbench
46.Selectthefunction“DefineContact”,clickonthegeometryandgiveitthename“CATELB_CONTACT_ELEC”
47.Selectthefunction“DefineCavityConnectionPoint”andclickonthegeometry.Giveitaname.
48.Selectonesideofthecontactasrepresentationandasacontactsurface.
49.Clickonthecontactaxisforthecoincidence.Thereisnoneedtodefinetheorientation.
50.Savethenewobjectwiththenewname.
51.Dothesamethingwith“CATELB_CONTACT2.CATPart”
Step7:
Addingtheelectricalpropertiestotheharnessconnector
52.Openthecomponent“CATELB_HARNESS_CONN_NO_CONTACT.CATPart”
53.Defineitasaconnectorusingthefunction“DefineConnector”andgiveitthename“CATELB_HARNESS_CONN_NO_CONTACT_ELEC”
54.Selectthefunction“DefineConnectorConnectionPoint”.Defineitsproperties.
55.Selectthefunction“DefineBundleConnectionPoint”.Defineitsproperties.
56.Savetheobjectwithname“CATELB_HARNESS_CONN_NO_CONTACT_ELEC.CATPart”
Step8:
Storethecomponentsintothecatalog
57.OpenalltheelectricalcomponentsyouhavedefinedinElectricalPartDesign
58.Foreachcomponent,selectthefunction“StoreinCatalog”andselecttherightfamily.
Step9:
Definetheassembly
59.Selectthefunction“CatalogBrowser”andopenthecatalog“CATELB_COMPONENTS_CATALOG_WITH_COMPONENTS.catalog”
60.Createanewfamilycalled“Assemblies”withinthecatalog
61.Savethecatalogandcloseit.
62.Selecttheworkbench“ElectricalAssemblyDesign”
63.Createanewproductandimportthecomponentsintoit.
64.Linkthecomponentstogetherusingthefunction“Link”
65.Storethenewassemblyintothecatalogueusingthe“StoreinCatalog”function.
DefineanElectricalEquipment
WewilldefinetheequipmentgeometryusingthestandardmechanicaldesigntoolsofCATIAV5.Thenextstepwillbetheelectricalpropertiesdefinition.Inthisexercise,ourequipmentwillbeabattery.
Step1:
Definingthegeometry
66.Createanewpart
67.Selectaplaneandopenthesketcher
68.Drawarectangle
69.Exitthesketcher
70.Createapadwiththesketch
71.Definethecavitiesgeometryusingthesametools
Step2:
Definingtheequipment
72.Createanewpart
73.Openthe“ElectricalPartDesign”workbench
74.Selectthe“DefineEquipment”function
75.Selectthepartrepresentingyournewbattery
76.GivethenewequipmentaPartNumber
77.ClickOk
Step3:
Definingthecavities
78.Selectthefunction“DefineCavity”
79.Clickonthepartcorrespondingtoyourbattery
80.Givethenewcavityanamee.g.Gnd.
81.Selectthesurfacewherethecavityis
82.Selectthecontactsurface
83.Selectthecoincidenceaxis
84.Repeatsteps1to6forthesecondcavity
Createanewcatalogandimportalistofwires
Wearegoingtocreateabrandnewcatalog.Wewillthenaddasetwiresintoit.
Step1:
Creatingacatalog
85.ClickonFile/New/CatalogDocument
86.Selectthefunction“AddFamily”andcreatethefamily“Wires”
87.Saveyournewcatalog:
clickonFileSave
88.Typethefilename“CATELB_CatalogOfWires.catalog”
Step2:
Importingasetofwires
89.Copythecatalogyouhavecreatedintothedirectory“c:
\Temp”
90.Copythefiles:
“CATELB_CreateWires.CATScript”and“CATELB_ListOfWires.csv”into“c:
\Temp”
91.Openthecatalog
92.SelectthefunctionTools/Macro/Macros
93.Selectthepath“c:
\Temp”in“Macrolibraries”and“Addexistinglibraries”
94.SelectthefileCATELB_CreateWires.CATScriptinthe“Availablemacros”window
95.Selectthefunction“Run”
96.Mapthecatalogfamilywith“Wire”
97.
Mapthekeyword“Name”withthePartNumber.
Createatotallydefinedequipment
Wearegoingtoconnectthebatterytoitsdevicesconnectorsandeachoneofthedeviceconnectorstotheharnessconnectors.
Step1:
Importthecomponents
98.Createanewproduct
99.Openthecatalogbrowser
100.Selectthecatalog“CATELB_COMPONENTS_CATALOG_WITH_COMPONENTS.catalog”
101.Selectthechapter“Equipments”
102.Selectthebatteryanddragittotheproduct
103.Selectthechapter“DeviceConnector”
104.Selectthecylindricalconnectoranddragittotheproduct.Doittwice.
105.Selectthechapter“HarnessConnector”
106.Selectthecylindricalharnessconnectoranddragittotheproduct.Doittwiceaswell.
107.Closethecatalog
108.Usethecompasstomovethecomponents.
Step2:
Connectthecomponents
109.Selecttheworkbench“ElectricalAssemblyDesign”
110.Selectthefunction“ConnectElectricalDevices”
111.Selectthefirstbatterycavity
112.Selectthefirstdeviceconnectorcavityconnectionpoint
113.Repeatsteps2to4withtheseconddeviceconnector
114.Selectthefunction“ConnectElectricalDevices”
115.Selectthefirstdeviceconnector“connectorconnectionpoint”
116.Selectthefirstharnessconnector“connectorconnectionpoint”
117.Repeatsteps6to8withthesecondharnessconnector
Create