LBHG2 发动待审核抽审OK.docx
《LBHG2 发动待审核抽审OK.docx》由会员分享,可在线阅读,更多相关《LBHG2 发动待审核抽审OK.docx(53页珍藏版)》请在冰豆网上搜索。
![LBHG2 发动待审核抽审OK.docx](https://file1.bdocx.com/fileroot1/2023-1/2/bae41317-fcda-4fba-b67d-9f8264dc4f4b/bae41317-fcda-4fba-b67d-9f8264dc4f4b1.gif)
LBHG2发动待审核抽审OK
2.13.7.11故障诊断代码章节索引
2.13.7.11IndexofDTCSections
水温传感器线路低电压
Enginecoolanttemperaturesensorcircuitlowvoltage
水温传感器线路高电压或断路
Enginecoolanttemperaturesensorcircuithighvoltageoropencircuit
碳罐控制阀线路短路到低电压或断路
Canistercontrolvalveshortcircuittolowvoltageoropencircuit
碳罐控制阀线路短路到高电压
Canistercontrolvalveshortcircuittohighvoltage
动力转向开关线路电压范围/性能故障
Powersteeringswitchcircuitvoltagerange/performancefault
巡航“On/Off”信号干扰
CruisecontrolON/OFFsignalnoisy
巡航“Cancel”信号干扰
CruisecontrolCANCELsignalnoisy
巡航“Resume”信号干扰
CruisecontrolRESUMEsignalnoisy
巡航“Set”信号干扰
CruisecontrolSETsignalnoisy
CAN总线关闭
CANbusoff
与TCM控制器通讯中断
CommunicationwithTCMcontrollerinterrupted
2.13.7.12DTCP0011,P0012,P0026
2.13.7.12DTCP0011,P0012andP0026
进气VVT电磁阀由主继电器提供工作电源,ECM以脉宽调制信号控制接地。
ThemainrelayprovidestheairintakeVVTsolenoidvalvewithoperatingpowersupply.ECMcontrolsthegroundingconditionwiththepulse-widthsignal.
进气凸轮轴位置执行器最大可使凸轮工作角度改变50°。
Theairintakecamshaftpositionactuatorcanchangethecamworkinganglefor50°asthemaximum.
发动机运转。
。
Theengineisrunning.
没有进行阀门清洗。
Thevalvecleaningisnotperformed.
凸轮轴转速小于15°/s。
Therotatingspeedofcamshaftislessthan15°/s.
凸轮轴位置大于10°,小于45°。
Thecamshaftpositionismorethan10°andlessthan45°.
占空比大于0.9,或小于0.1.
Thedutycycleismorethan0.9orlessthan0.1.
凸轮轴位置错误大于15°。
Thecamshaftpositionerrorismorethan15°.
凸轮轴位置大于45°。
Thecamshaftpositionismorethan45°.
凸轮轴位置错误大于20°。
Thecamshaftpositionerrorismorethan20°.
检查控制系统是否存在除DTCP0011,P0012,P0026以外的故障代码
CheckwhetherthereisanyotherDTCofcontrolsystemthanDTCP0011,P0012andP0026.
是否存在除DTCP0011,P0012,P0026以外的故障代码。
IsthereanyotherDTCthanDTCP0011,P0012andP0026?
断开VVT电磁阀线束连接器EM41。
DisconnectharnessconnectorEM41ofVVTsolenoidvalve.
2.13.7.13DTCP0016
2.13.7.13DTCP0016
凸轮轴齿距偏移小于0.13,或大于0.36。
Thecamshaftpitchdeviationislessthan0.13ormorethan0.36.
齿距检测启用时,当齿距初始学习(发动机起动时)或重新学习(回到怠速时)。
Withpitchtestenabled,duringinitialpitchlearning(incaseofenginestarting)orrelearning(incaseofreturningtoidling).
2.13.7.14DTCP0068,P0106
2.13.7.14DTCP0068andP0106
进气压力温度传感器测量因发动机负载、进气歧管真空和转速变化而造成的进气歧管压力变化,并将这些变化转换为电压输出发动机控制模块(ECM)。
Theintakepressureandtemperaturesensormeasurestheintakemanifoldpressurevariationcausedbytheengineload,intakemanifoldvacuumandrotatingspeedchange,andthenconvertssuchvariationintovoltageoutputtoenginecontrolmodule(ECM).
同时发动机控制模块(ECM)根据节气门位置变化量,来比较实际和预测进气歧管绝对压力的变化,从而检测进气歧管绝对压力传感器是否对节门位置的变化进行响应。
Meanwhile,enginecontrolmodule(ECM)predictsthechangeofintakemanifoldabsolutepressureinapracticalwaybasedonthevariationvolumeofthrottleposition,soastocheckwhethertheintakemanifoldabsolutepressuresensorrespondstothevariationofthrottleposition.
依此设定DTCP0106故障。
DTCP0106issetonsuchbasis.
发动机控制模块(ECM)根据进气压力温度传感器所测的数据确定空气流量,并将其与预测的节气门位置空气流量值进行比较。
Enginecontrolmodule(ECM)determinestheairflowbasedonthedataofintakepressureandtemperaturesensorandcomparesthedeterminedflowwiththeparticipatedthrottlepositionairflow.
如果发动机控制模块(ECM)检测到当前进气压力温度传感器实际检测到的空气流量与基于节气门位置传感器期望空气流量不一致,将设置DTCP0068故障。
Ifenginecontrolmodule(ECM)detectsthattheactualairflowdetectedbycurrentintakepressureandtemperaturesensorisdifferentfromtheexpectedairflowofthrottlepositionsensor,DTCP0068willbeset.
进气压力温度传感器检测到的空气流量值与预测的节气门位置空气流量值相差200g/s。
Thedeferencebetweentheactualairflowvaluedetectedbyintakepressureandtemperaturesensorandtheexpectedairflowvalueofthrottlepositionsensoris200g/s.
无进气压力传感器故障。
Thereisnofaultofintakepressuresensor.
进气歧管及真空管
Intakemanifoldandvacuumpipe
大气压修正压力值大于高限值或小于低限值。
Correctedbarometricvalueismorethanupperlimitorlessthanlowerlimit.
检查控制系统是否存在除DTCP0068P0106以外的故障代码。
CheckwhetherthereisanyotherDTCofcontrolsystemthanDTCP0068andP0106.
除DTCP0068,P0106以外的DTC
OtherDTCthanDTCP0068andP0106
DTCP0068P0106
DTCP0068P0106
检查故障诊断仪数据列表中大气压力参数。
CheckthebarometricpressureparameterinDiagnosticInstrumentDataList.
比较大气压力参数值与实际的大气压力值。
Comparethebarometricpressureparametervaluewiththeactualbarometricpressurevalue.
参见“4G18-E发动机控制系统中的
See“”sectionin4G18-EEngineControlSystem.
两者是否相近?
Arethetwovaluesclose?
检查发动机运转时进气压力传感器数值。
Checkthereadingofintakepressuresensorwhentheengineisrunning.
怠速时,观察进气压力传感器数值。
Withtheengineidling,checkthereadingofintakepressuresensor.
加速时,观察进气压力传感器数值。
Withtheengineaccelerating,checkthereadingofintakepressuresensor.
进气压力传感器数值是否变化?
Doesthereadingofintakepressuresensorchange?
检查进气压力温度传感器。
Checkintakepressureandtemperaturesensor.
在不断开进气压力温度传感器的线束连接器情况下,将进气压力温度传感器从进气歧管上拔出,并使用真空泵,将真空泵的气管安装在进气压力温度传感器上。
Withharnessconnectorofintakepressureandtemperaturesensorconnected,pulloutthesensorfromtheintakemanifold,andinstalltheairpipeofvacuumpumptothesensor,soastousethevacuumpump.
进气压力温度传感器上施加50Kpa的压力。
Applyapressureof50Kpaontotheintakepressureandtemperaturesensor.
进气压力温度传感器数值是否变化?
Doesthereadingofintakepressureandtemperaturesensorchange?
检查进气压力传感器值参数变化响应。
Checktheresponseofintakepressuresensorreadingtotheparameterchange.
改变节气门位置后,卡住节气门,观察此时进气歧管压力传感器参数值,是否根据节气门位置的变化迅速改变。
Afterthethrottlepositionchanges,getthethrottlepositionstuckandcheckthereadingofintakemanifoldpressuresensoratthemomenttoseewhetherthereadingchangesquicklyalongwiththethrottleposition.
进气压力传感器数值是否快速变化?
Doesthereadingofintakepressuresensorchangequickly?
检查进气压力温度传感器安装端口及真空管。
Checktheinstallationportandvacuumpipeofintakepressureandtemperaturesensor.
查进气压力温度传感器安装端口及真空管。
Checktheinstallationportandthevacuumpipeofintakepressureandtemperaturesensor.
是否存在安装端口及真空管堵塞?
Aretheinstallationportandvacuumpipeblocked?
清理、维修进气歧管及真空管。
Cleanandrepairintakemanifoldandvacuumpipe.
更换进气压力温度传感传感器。
Replaceintakepressureandtemperaturesensor.
2.13.7.15DTCP0076,P0077
2.13.7.15DTCP0076andP0077
进气凸轮轴位置(CMP)执行器连接在进气凸轮轴上并由液压进行操动,液压压力由机油泵提供,以改变进气凸轮轴相对于曲轴位置传感器(CKP)的角度。
Theairintakecamshaftposition(CMP)actuatorisconnectedtotheairintakecamshaftandisdrivenbyhydraulicpressureprovidedbyoilpumptochangetherelativeangleofthecamshafttothecamshaftpositionsensor(CKP).
进气OCV阀由主继电器提供工作电源,ECM以脉宽调制信号控制接地。
ThemainrelayprovidestheairintakeOVCvalvewithoperatingpowersupply.ECMcontrolsthegroundingconditionwiththepulse-widthsignal.
机油压力使固定在凸轮轴前部的凸轮轴位置执行器机构内的一个安全滑阀动作。
Theoilpressuredrivesasafeguidingvalveinthecamshaftpositionactuatormechanismfixedinthefrontofthecamshafttomove.
当安全滑阀动作时,机油被导入凸轮轴位置执行器,使凸轮轴旋转。
Whenthevalvemoves,theoilwillbeguidedintothecamshaftpositionactuator,sothatthecamshaftwillstartrotating.
进气凸轮轴位置执行器最大可使凸轮工作角度改变50度。
Theairintakecamshaftpositionactuatorcanchangethecamworkinganglefor50degreesasthemaximum.
ECM通过ECM线束连接器EM01的43号端子控制电磁阀内部接地。
ECMcontrolstheinternalgroundingofsolenoidvalvebyconnectingterminal43ofECMharnessconnectorEM01.
ECM内部有一个反馈电路。
ThereisafeedbackcircuitinsidetheECM.
发动机ECM通过监测反馈信号来确定控制电路是否开路、对接地短路或对电压短路。
EngineECMmonitorsthefeedbacksignalstodeterminewhetherthecontrolcircuitisopen,shorttogroundorshorttovoltage.
如果发动机ECM在控制电路被指令断开时检测到控制电路电压在预定范围内,则设置故障诊断码。
Whenthecontrolcircuitisopenuponcommand,ifengineECMdetectsavoltagewithinthepredeterminedrange,theDTCwillbeset.
进气OCV阀输出电压不符合ECM的预定范围。
TheoutputvoltageofOCVvalveisnotwithinthepresetrangeofECM.
没有相应故障码存在。
ThereisnorelatedDTC.
发动机运转大于0.5s
Theenginehasbeenrunningformorethan0.5s.
启动时间延迟大于0.5s。
Thestartingdelayismorethan0.5s.
电磁阀电路
Solenoidvalvecircuit
测量进气OCV阀总成的电阻值。
MeasuretheresistancevalueofintakeOCVvalveassembly.
断开进气OCV阀线束连接器EM41。
DisconnectharnessconnectorEM41ofintakeOCVvalve.
测量进气OCV阀的1号和2号端子间的电阻值。
Measuretheresistancebetweenterminal1andterminal2ofintakeOCVvalve.
标准电阻值:
20℃(68ºF)时为7.2Ω
Standardresistancevalue:
7.2Ωat20°C(68°F)
更换进气OCV阀总成,转至步骤7。
ReplaceintakeOCVvalveassemblyandgotoStep7.
测量进气OCV阀供电线路。
MeasuretheintakeOCVvalvepowersupplycircuit.
测量进气OCV阀线束连接器EM41的1号端子与接地之间的电压。
Measurethevoltagebetweenterminal1ofintakeOCVvalveharnessconnectorEN41andtheground.
检查进气OCV阀控制线路。
InspectcontrolcircuitofintakeOCVvalve.
断开ECM线束连接器EM01。
DisconnectECMharnessconnectorEM01.
测量进气OCV阀线束连接器EM41的2号端子与ECM线束连接器EM01的43号端子之间的电阻值,检查是否存在断路情况。
Measuretheresistancebetweenterminal2ofintakeOCVvalveharnessconnectorEM41andterminal43oftheECMharnessconnectorEM01;checkwhetherthereisanopencircuit.
测量进气OCV阀线束连接器EM41的2号端子与接地之间的电阻值,检查是否存在对地短路情况。
Measuretheresistancebetweenterminal2ofintakeOCVvalveharnessconnectorEM41andtheground;checkwhetherthereisashortcircuittoground.
测量进气OCV阀线束连接器EM41的2号端子与接地之间的电压值,检查是否存在对电源短路情况。
Measurethevoltagebetweenterminal2ofintakeOCVvalveharnessconnectorEM41andtheground;checkwhetherthereisashortcircuittopowersupply.
EM41
(2)-EM01(43)间电阻
ResistancebetweenEM41
(2)andEM01(43)
EM41
(2)-接地间电阻
ResistancebetweenEM41
(2)andground
EM41
(2)-接地间电压
VoltagebetweenEM41
(2)andground
2.13.7.16DTCP0105,P0107,P0108
2.13.7.16DTCP0105,P0107andP0108
ECM通过ECM线束连接器EM01的66号端子给传感器线束连接器EM16的2号端子提供5V参考电压。
ECMprovides5Vreferencevoltagetoterminal2ofsensorharnessconnectorEM16throughterminal66ofECMharnessconnectorEM01.
同时