XDM告警列表.docx
《XDM告警列表.docx》由会员分享,可在线阅读,更多相关《XDM告警列表.docx(19页珍藏版)》请在冰豆网上搜索。
XDM告警列表
ListofxdmalarmsXDM告警列表
WrittenbySunny16-June-2004
1.TransmissionAlarms传输告警
Alarmname告警名称
ProbableCause可能的原因
LOS信号丢失
Indicatesasignificantdropinreceivesignallevel
canbecausedbybrokenfiber,fibercuts,disconnectedfiberorfaulty
opticaltransmitter.
指示光接口或电接口的收端没有信号输入。
产生原因:
接口收端电缆线断了,2M/155M头不好,没上业务等;光缆断了,光接口对端没发光等。
LOD数据丢失
LossofDatarepresentsthecaseinwhichopticalLOSisnotbeingdetectedbutnosignaltransitionsexist.
光接口收不到信号但又检测不到LOS时产生此告警。
例如光接口连到纯光源上时产生LOD。
LOP指针丢失
Invalidpointersarereceivedduetoequipmentfailureormismatch
insignalmappingortimingproblems.
设备故障,信号映射失配或时钟问题。
LOF帧丢失
Indicatesnodetectofframealignmentintheincomingsignal
接收的信号中没有监测到帧队列
AIS告警指示信号
Indicatesupstreamfailure.indicatesthatanotheralarmexistsprevioustotheequipmentsendingtheAIS.
指示上游失败。
指示另外一个告警,即上游那个发送AIS信号的设备存在的告警。
AU/TUAIS管理单元或时隙的告警指示信号
Indicatesupstreamfailure.indicatesthatanotheralarmexistsprevioustotheequipmentsendingtheAIS.
指示上游失败。
指示另外一个告警,即上游那个发送AIS信号的设备存在的告警。
SSF服务信号失败
Serversignalfailure.IndicatesfailureinadaptationfunctionduetoAU_AISorAU_LOP.
服务信号失败。
指示基于AU_AIS或AU_LOP的相应功能失败。
.
EXC误码率过高
TheBitErrorRate(BER)ontheincomingsignalframeishigherthanaspecificconfiguredthreshold.
接收信号帧误码率高于一个特定门限值
DEG信号劣化
TheBitErrorRate(BER)ontheincomingframeishigherthanaspecificconfiguredthreshold.ThisthresholdislowerthantheonespecifiedforEXC
接收信号帧误码率高于一个特定门限值。
但这个门限值低于产生EXC的门限值。
RDI远端接收失败
Remotedefectindicationreceived,indicatingfarendsignalfailcondition.
远端接收失败,指示远端失败情况。
RAI远端接收失败
Remotedefectindicationreceived,indicatingfarendsignalfailcondition.
远端接收失败,指示远端失败情况。
TIM通道匹配缺失跟踪指示
TraceIdentifierMismatchdefect
causedbyamisprovisioningoftheexpectedtraceormisconnection
(ThealarmisresultofcompareoftheexpectedJ0/J1/J2bytetothereceivedone)
通道匹配缺失跟踪指示。
产生原因:
通道属性期望值定义不正确,错误的连接(此告警是J0/J1/J2字节收到的值与期望值对比的结果)。
UNEQ卷标不匹配
Unequippedsignalisdetected
CanbecausedbydisconnectedTrail.
卷标不匹配,可由电路不完整造成。
PLM净负荷信号卷标不匹配
Amismatchinthepayloadsignallabelisdetected.
检测到净负荷信号卷标不匹配。
LOM复帧丢失
Thisalarmindicatesalossofmultiframealignmentontheincomingsignal.
指示接收信号复帧队列丢失。
LOMC级联电路复帧丢失
lossofmultiframealignmentrelatedtoconcatenatedTrails
级联电路复帧丢失
LOA级联电路接收队列丢失
Lossofalignmentinincomingconcatenationsignal
级联电路接收队列丢失。
SQM序列不匹配
Lossofsequencedefectinvirtualconcatenationsignal
Canbecausedbymismatchinconnectionswhichasresultthereceivedsequencenumberofavc4doesnotmatchtheexpectedSequencenumber.
虚级联电路序列丢失。
在高阶电路的vc4连接中,当vc4的接收序列数与期望序列数不一致时,可产生此告警。
MSPLFailureMSPL失败
Inbidirectionaloperationmode:
ReceivingoffaultyK1K2bytes,Noanswerfromthefarendnode,failureofExercisecommand.
在双向操作模式中:
K1K2字节接收错误,远端节点无应答,MSPL倒换演练失败都会产生此告警。
PJ_15M15分钟指针调整
Thepointerjustificationcountexceedsapredeterminedvalue.
指针调整数超过规定值。
UAT不可用时间
Consecutive10secondsofseverityerrorseconds
连续10秒严重误码秒.
BBENE15Min15分钟近端背景误码块
Crossingthe15min.BackgroundBlockErrorsthreshold(atnearend)
15分钟时间单元性能监测,近端背景误码块超过门限值。
ESNE15Min15分钟近端误码秒
Crossingthe15min.errorsecondsthreshold(atnearend)
15分钟时间单元性能监测,近端误码秒超过门限值。
SESNE15Min15分钟近端严重误码秒
Crossingthe15min.Severityerrorsecondsthreshold(atnearend)
15分钟时间单元性能监测,近端严重误码秒超过门限值。
BBENE1Day24小时近端背景误码块
Crossingthe1dayBackgroundBlockErrorsthreshold(atnearend)
24小时时间单元性能监测,近端背景误码块超过门限值。
ESNE1Day1天近端误码秒
Crossingthe1day.errorsecondsthreshold(atnearend)
24小时时间单元性能监测,近端误码妙超过门限值。
SESNE1Day1天严重误码秒
Crossingthe1daySeverityerrorsecondsthreshold(atnearend)
24小时时间单元性能监测,近端严重误码秒超过门限值。
BBEFE15Min15分钟远端背景误码块
Crossingthe15min.BackgroundBlockErrorsthreshold(atfarend)
15分钟时间单元性能监测,远端背景误码块超过门限值。
ESFE15Min15分钟远端误码秒
Crossingthe15min.errorsecondsthreshold(atfarend)
15分钟时间单元性能监测,远端误码秒超过门限值。
SESFE15Min15分钟远端严重误码秒
Crossingthe15min.Severityerrorsecondsthreshold(atfarend)
15分钟时间单元性能监测,远端严重误码秒超过门限值。
BBEFE1Day24小时远端背景误码块
Crossingthe1dayBackgroundBlockErrorsthreshold(atfarend)
24小时时间单元性能监测,远端背景误码块超过门限值。
ESFE1Day24小时远端误码秒
Crossingthe1day.errorsecondsthreshold(atfarend)
24小时时间单元性能监测,远端误码秒超过门限值。
SESFE1Day24小时远端严重误码秒
Crossingthe1daySeverityerrorsecondsthreshold(atfarend)
24小时时间单元性能监测,远端严重误码秒超过门限值。
1.1.TransmissionalarmsrelatedtoOpticalpowercontrol
光功率控制相关传输告警
PWR_CTL_OUT_OF_TRACKING_LIMITATION
光功率控制超限
RequiredcorrectionisgreaterthanTrackingLimitandhadbeensuppressed
必需的修正值超出跟踪门限,调整被抑制。
PWR_CTL_SPAN_LOSS_CHANGE
光功率控制跨度
RequiredcorrectionisgreaterthanLowAlarmThresholdandhadbeenadded
必需的修正值大于最低告警极限
PWR_CTL_OUT_OF_SET_CAPABILITY
光功率控制输出超出接收机实际能力
Requiredcorrectionisbeyondthegaincapabilityofthecard.Thesetcorrectionislessthantherequired.
必需的修正值超过光卡放大能力。
接收机修正值小于要求值。
PWR_CTL_OUTPUT_PWR_INCORRECT
光功率控制输出功率不正确
Requiredcorrectionisbeyondthegaincapabilityoftheequipment.Thesetcorrectionislessthantherequired.
必需的修正值超过设备放大能力。
接收机修正值小于要求值。
PWR_CTL_GAIN_BLOCK_INPUT_OVERLOAD
光功率控制放大区输入过载
GaininputOverload
输入放大过载
1.2.TransmissionalarmsrelatedtoEthernetandL2
以太网和2层相关传输告警
ANFailure
Auto-negotiationFailure
自动协商失败
ANAbilityMismatch
Auto-negotiationAbilityMismatch–Whenthetotalabilityofthelinkisnotused,i.e.aFastEthernetlinkisoperatingata10Mb/sspeed.
PartnerOffline
Remote/PartnerhasbeenindicatedasOfflineoradministrativelyOutofService.
PartnerLinkDown
Remote/PartnerLinkdown
PartnerANFailure
Auto-negotiationfailureofthelinkpartner
LinkDown
Ethernetlinkdownorlossofcarrier(asdefinedinIEEE802.3)
RxBufferOverflow
FIFObufferoverflowoftheingresstraffic
TxBufferOverflow
FIFObufferoverflowoftheegresstraffic
CSF
ClientServerFailed–Failureintheupstreamclientsignal
TSF
TrailSignalFail–ifthereisafailureononeofthepathterminationthatcomposethevirtuallyconcatenatedEoStrail.
TSD
TrailSignalDegrade–ifthereisasignaldegradeononeofthepathterminationthatcomposethevirtuallyconcatenatedEoSEoStrail.
SSF
LossofFrame.LossofFramedelineationattheGFPlayer.
LOTC
LossofTotalCapacity–whenLCASissupportedthisindicatesthatnoneofthepathterminationarecurrentlycarryingtrafficduetoafailure.
LOPC
LossofPartialCapacity–whenLCASissupportedindicatesthatoneormoreoftheprovisionedpathterminationarenotcurrentlycarryingtrafficduetoafailure.
InDiscards
Thresholdalarmthatisraisedwhenthenumberofdiscardedframesontheportexceedsaconfigurablevalue
WANTxUtilization
ProvidesameasureoftheWANlinkutilizationwithrespectedtotheactivebandwidth
ANFailure
Auto-negotiationFailure
PartnerOffline
Remote/PartnerhasbeenindicatedasOfflineoradministrativelyOutofService.
PartnerLinkDown
Remote/PartnerLinkdown
PartnerANFailure
Auto-negotiationfailureofthelinkpartner
LinkDown
Ethernetlinkdownorlossofcarrier(asdefinedinIEEE802.3)
BroadcastPkts
Thresholdalarmraisedwhenthenumberbroadcastpacketsreceivedonaportexceedsaconfigurablevalue.
MulticastPkts
Thresholdalarmraisedwhenthenumbermulticastpacketsreceivedonaportexceedsaconfigurablevalue
InErrors(Packets)
Thresholdalarmthatisraisedwhenthenumberofreceivederrorframesperportgoesoveraconfigurablevalue.
InErrors(Octets)
Thresholdalarmthatisraisedwhenthenumberofreceivederroroctetsperportgoesoveraconfigurablevalue
DuplicateMACAlert
IfdetectingaduplicateMACaddress(thisisa15minTCAwithadefaultthresholdof1).
RandomDropOctets-CoS
RandomdropoctetsperportoregressqueueforeachClassofService.Configurablethresholdalarm
RandomDropOctets-CoS
RandomdropoctetsperportoregressqueueforeachClassofService.Configurablethresholdalarm
RandomDropOctets-CoS
RandomdropoctetsperportoregressqueueforeachClassofService.Configurablethresholdalarm
RandomDropOctets-CoS
RandomdropoctetsperportoregressqueueforeachClassofService.Configurablethresholdalarm
BSCDiscardSeconds
ThresholdalarmraisedwhenthenumberofsecondsthattheBroadcastStormControlhasbeendroppingframesexceedsaconfigurablevalue.
2.
ServiceAlarms服务告警
ServiceFailure服务失败
ServiceFailureindicatesthattheserviceisfailed.Themainpathandprotectionpathsarenottransmittingtraffic.
指示服务失败。
主通道和保护通道都没传送业务。
ServiceDegraded服务劣化
ServiceDegradeindicatesthatacrossconnectthatispartofatrailistransmittingtrafficbutthatthetrafficisrecoginzedasbeingdegraded
指示通道性能劣化。
ProtectionPathFailure保护通道失败
ProtectionPathFailure-indicatesthattheprotectionpath(thatwhichiscurrentlynotusedfortheactivetraffic)ofatrailtransmittingtrafficisfailed.Theactivepathistransmitting.
保护通道失败,但主通道正常工作。
ProtectionPathDegraded保护通道劣化
ProtectionPathDegradeindicatesthattheprotectionpath(thatwhichiscurrentlynotusedfortheactivetraffic)ofatrailtransmittingtrafficisdegraded.Theactivepathistransmittingwithoutandegradation.
保护通道性能劣化,但主通道正常工作。
3.Timingalarms时钟告警
Alarmname
ProbableCause
TGHoldOver时钟保持
TheTimingGeneratorhasnoavailabletimingreferenceforsynchronization.ThereforeitenterstoHoldOverstateinwhichitkeepsitslaststatewhenithadsynchronizationsource.
时钟发生器没有可用的同步时钟参考源。
因此它进入时钟保持状态,锁定当它有同步时钟源最后一刻的状态。
时钟保持模式与同步时钟源最后一刻的频率和相位同步。
PrimaryTimingSourceNotActive第一位优先时钟源不工作
Thisindicationinformstheuserthatthesystemhasswitchedtoadifferenttimingsourcefromt