SAEUSCAR2Rev3汽车电子连接器性能标准解析Word下载.docx
《SAEUSCAR2Rev3汽车电子连接器性能标准解析Word下载.docx》由会员分享,可在线阅读,更多相关《SAEUSCAR2Rev3汽车电子连接器性能标准解析Word下载.docx(103页珍藏版)》请在冰豆网上搜索。
这些规程只适用于线路中连接器系统中、针类连接器系统中和设备连接器系统中的端子,但不适用于“边板连接器系统”(EdgeBoardconnectorsystems),>
交/直流20伏,或针孔(eyelet)型的端子。
Notethatthisspecificationdoesnotcoverthemechanicalassistportionsofconnectorsthatincludesuchdevices.TheAuthorizedPersonmustprovidedetailsofanyadditionaltestingdesiredtovalidatethesemechanismsaspartofthetestrequest/order。
注意本规范并没有包含连接器的辅助机械部份。
负责人必须提供相关额外测试的信息以满足这些机械作为测试一部分的要求。
IMPORTANTNOTICE:
Inanyintendedvehicleapplication,iftheproductscoveredbythisspecificationare,ormaybe,subjectedtoconditionsbeyondthosedescribedinthisdocument,theymustpassspecialtestssimulatingtheactualconditionstobeencounteredbeforetheycanbeconsideredacceptableforactualvehicleapplication.Bywayonlyofexample,thisincludesproductsthatmaybesubjectedtotemperaturesbeyondtheextremesofClass4inFigure5.1.4,ormaybesubjectedtoshockorvibrationintheunsprungportionsofavehicle,suchasthewheelhub.Productscertifiedbytheirsupplierashavingpassedspecificapplicableportionsofthisspecificationarenottobeusedinapplicationswhereconditionsmayexceedthoseforwhichtheproducthasbeensatisfactorilytested.
重要提示:
如果被测试零件是用于一些超过本规范所规定范围的车辆,这些零件必须通过和实际情况的相一致的模拟测试才能投入正式使用。
例如,这些包括在图5.1.4中显示的超过4级的极端温度、非扭转(unsprung)部分例如轮轴(hub)的振动及摇摆。
已通过本规范测试标准的零件不应在超过其测试条件的条件下使用。
TheAuthorizedPersonisthefinalauthorityastowhattestsaretobeperformedonhisorherpartsandforwhatpurposethesetestsarerequired.Heorsheisalsothefinalauthorityforresolvinganyquestionsrelatedtotestingtothisspecificationandtoauthorizinganydeviationstotheequipmentorprocedurescontainedinthisspecification.Anysuchdeviationmustbedocumentedandincludedinthefinaltestreport.
负责人最终决定对零件进行何种测试及测试目的,他/她亦解决任何有关测试的问题并允许设备及程序的偏差。
所有这类偏差都必须有所记录并包括在最终测试报告中。
GuidanceastotherecommendedtestsforselectedpurposesisgiveninthechartsinAppendixCandD.IntheabsenceofcontrarydirectionfromtheAuthorizedPersoninthetestrequest/order,allelectricalconnectorsandtheirassociatedterminalsandothercomponentsarerequiredtomeetallapplicableportionsofthisdocumentwiththefollowingexception.
推荐测试的指导可以在附录C和D的图表中找到。
如果负责人没有相反的指示,所有电子连接器及其相关端子和部件都需要符合本文的规定,但有以下例外:
A.SpecificteststhatarenotrequiredoradditionaltestrequirementsasspecifiedinanydocumentinthehierarchyofSection3.0.
A.没有明确要求的测试或在第三部分各层次中规定了额外测试要求的。
2.0OUTLINE&
GLOSSARYOFTERMS大纲和术语表
2.1GENERAL通则
Diagramsareprovidedwherenecessarytoclarifythedetailsofthevarioustestprocedures.Thetestsineachsectionmustbeperformedintheordergivenunlessotherwisespecifiedinthetestrequest/order.Constructiondetailsforselectedtestfixturesandequipmentareprovidedinthisspecification.
在有必要协助明确各测试程序的细节的地方,本文提供图表。
除了特别指出之外,所有测试都必须按照给定的顺序执行。
本规则提供测试设备和装置的安装信息。
AglossaryoftermsisprovidedinAppendixB.Termsdefinedinthedefinitionsorglossaryarecapitalized(i.e.RoomTemperature,SteadyState,PLR,etc.).AlistofdefinitionsisprovidedinAppendixA.
附录B提供术语表。
术语单词都用大写开头(如:
RoomTemperature,SteadyState,PLR等)。
附录A提供定义表。
Forthepurposesofthisspecificationthereareonlytwotypesofelectricalconnector:
sealedandunsealed.
为了说明的目的,本规范只有两种连接器:
密封型和不密封型。
3.0REFERENCEDDOCUMENTSREQUIRED要求参考文献
3.1DOCUMENTHIERARCHY文件等级层次
Intheeventthereisaconflictbetweenperformancestandards,partdrawings,andotherrelatedstandardsorspecifications,therequirementsshallbeprioritizedasfollows:
当性能标准、零件图纸和其它相关标准及规则发生不一致时,优先级顺序如下:
1st-ApplicableFMVSSrequirementsandotherapplicablestateandFederalrequirements.
2nd-Applicablepartdrawings
3rd-Applicableproductdesignspecification(s).
4th-AutomotiveIndustryActionGroup(AIAG)ProductionPartApprovalProcess(PPAP)
5th-ApplicableUSCAR/EWCAPperformancestandards
6th-Otherapplicablestandardsandspecifications
1–适用的FMVSS和其它的州及美国联邦规定
2–适用的零件图纸
3–适用的产品设计规范
4–汽车行业工作组(AIAG)的生产零件批准过程(PPAP)
5–适用的USCAR/EWCAP性能标准
6–其它适用的标准和规范
3.2PARTDRAWING零件图纸
Thepartdrawingforeachconnectionsystemcomponentshouldcontainorreference:
每个连接系统的零件图纸都应该包含或指定以下内容:
A.Alldimensionalrequirements(whichmustbeinGD&
Tformat).
B.Performancerequirements.
C.Componentpartnumber.
D.Referencetoapplicableportionsofthisspecification.
E.Thequantityandpartnumberofterminalsused.
F.Thetypicalmatingconnectorandterminals.
G.MaximumpermissibleTemperatureClass(perFigure5.1.4)forwhichthepartisintendedorhasbeensuccessfullytested.
A.所有规定尺寸(必须用GD&
T格式)
B.性能要求
C.部件号
D.适合本规范部分的参考。
E.使用端子的数量及零件号
F.典型的连接器和端子的装配。
G.零件计划使用或已经成功测试的最大允许温度等级(根据图5.1.4)
Forpurposesofcontrolandstandardization,eachdrawingthatcontainsapartoradevicethatincludesanelectricalreceptacleconformingtoaUSCAR/EWCAP"
footprint,"
mustcontainthefollowingstatementinthedrawingnotesorotherprominentplace:
为了便于控制及标准化起见,每个包含有符合USCAR/EWCAP"
footprint"
的电容器的图纸也必须在图纸说明或其它显著位置标明以下声明:
NOTICE注意
Thisdrawing,iscontrolledbytheElectricalWiringComponentsApplicationPartnership(EWCAP),asubgroupoftheUnitedStatesConsortiumforAutomotiveResearch(USCAR).USCARisapartnershipbetweenDaimlerChryslerCorporation,FordMotorCompanyandGeneralMotorsCorporation.AnychangetoaEWCAPdrawing,includinga"
recordchange,"
mustbeapproved,inwriting,bytheresponsibleEWCAPmemberfromeachUSCARCompany.EachEWCAPmemberauthorizedtosignforhisorherCompanyisresponsibleforobtainingallnecessaryapprovalswithinthatCompanypriortosigningforapprovalofthechange.EWCAPexpresslyprohibitsanypartyfromchangingeitheranyEWCAPcontrolleddrawingoranyassociatedtoolingbeforereceivinganapprovalsignedbyanauthorizedrepresentativefromeachEWCAPpartner.Referencetothesignedapprovalformmustbeenteredinthisdrawing'
scontrolcolumn.
该图纸由美国汽车研究协会(USCAR)所属的电子线路零件应用协会(EWCAP)控制。
USCAR是戴姆勒-克赖斯勒集团、福特汽车公司和通用汽车集团之间的合伙机构。
对于一个EWCAP图纸的任何一个改动,包括一个“记录变化”,都必须得到来自各个USCAR公司EWCAP相关成员的书面许可。
每个被授权的EWCAP成员在代表其公司签字前都必须得到其公司内部各相关方的批准。
EWCAP明确禁止任何一方在得到所有EWCAP成员认可之前擅自改动EWCAP控制图纸或任何对应模具。
在该图纸的控制栏中必须填写同意改动签字的相关证明内容。
3.3PRODUCTDESIGNSPECIFICATION产品设计规范
Theproductdesignspecificationmayormaynotbeanintegralpartofthepartdrawing.Instructionsmustbeincludedintheproductdesignspecificationforanyspecialtestsrequiredfortheassociatedpartandforanyexceptionsormodificationstothegeneralspecificationsandrequirementsinthisdocument.
产品设计规范可能是也可能不是零件图纸中独立的部分。
如要求相关零件进行特别测试,或对本档中的普通规范及要求做改动或,在产品设计规范中必须说明。
3.4TESTREQUEST/ORDER测试要求/顺序
3.4.1Samples,TestTypeandSpecialTests样品、测试类型和特殊测试
Thelaboratorytestrequest/ordershallprovidelocationanddocumentationoftestsamples,identifythetypeoftesttobeperformed(development,validation,specialpurpose,etc.)anddescribeanyspecialteststhatarenotapartofthisspecification.Anyrequiredrevisionsto,ordeviationsfrom,anytestsinthisspecificationmustincludedetailedinstructionsforeachchange.
实验室测试要求/顺序应该提供测试样品的地点和档、明确将要进行的测试的种类(研发、确认、特别目的等)并描述所有不属于本规范的特殊测试。
任何对于本规范中测试的改动或偏离都必须有详细说明。
3.4.2TestRequest/OrderInstructions测试要求/顺序指示
Instructionsmustbeincludedinthetestrequest/orderconcerningapplicabletestsandtheorderinwhichthetestsaretobeperformedifdifferentthanoutlinedbythisspecification.
如果测试要求/顺序和本规范的内容有所不同,必须加以说明。
3.4.3PerformanceandDurabilityTestInstructions性能和持久性测试说明
Instructionsmustbegiveninthetestrequest/orderconcerninglimitsforperformanceanddurabilitytests,includingdefinitionoftheconditionsunderwhichthoselimitsapply,iftheyaredifferentthanoutlinedinthisspecification.
如果对于性能和持久性测试的测试要求/顺序(包括极限环境条件的定义)和本规范不同,必须加以说明。
3.4.4DevelopmentTests研发测试
Developmenttestsarefrequentlyusedtoevaluatespecificareasofthedesign.Theyareatoolforevaluatingdesignalternatives,proposedimprovements,costreductionproposals,ordeterminingrootcausesoffieldproblems.
为评估设计的特定领域会经常使用研发测试,它们是评估其它可能设计方案或改进方案、降低成本和发现实际使用中出现问题的根本原因的有效工具。
3.4.5ValidationTests确认测试
Validationtestsorsampleapprovaltestsareacceptancetypetests.Considerationmustbegiventotheinherentrepeatabilityorsubject